Nissan Rogue (T33) 2021-Present Service Manual: U214f-83 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Chassis Control :: Dtc/circuit Diagnosis / U214f-83 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
U214F 83 CAN communication error (BCM) Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold BCM in malfunctioning.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication system

  • BCM

FAIL-SAFE

The following functions are suspended.

Automatic brake hold function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Ignition switch OFF to ON.

    CAUTION:

    Be sure to wait of 10 seconds after ignition switch OFF or ON.

  2. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U214F-83” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Erase self-diagnosis result for “CHASSIS CONTROL”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U214F-83” detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK BCM SYSTEM (1)

With CONSULT

  1. Erase self-diagnosis result for “BCM”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “BCM”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 3.

CHECK BCM SYSTEM (2)

  1. Ignition switch OFF.

  2. Disconnect BCM harness connector.

  3. Check BCM harness connector terminals (CAN communication line) for damage or loose connection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

ERASE SELF-DIAGNOSIS RESULT

With CONSULT

  1. Connect BCM harness connector.

  2. Erase self-diagnosis result for “CHASSIS CONTROL”.

  3. Ignition switch OFF and wait for 10 seconds or more.

>>

INSPECTION END

    U214f-57 Mac Comm Error (bcm)
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U214F 57 CAN communication error (BCM) Diagnosis condition — Signal (terminal) — Thr...
    U214f-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U214F 87 CAN communication error (BCM) Diagnosis condition When ignition switch is ON. S...

    Other materials:

    Symptom Diagnosis. Easy Fill Tire Alert Does Not Activate
    Description The easy fill tire alert does not function while inflating a tire when the CVT shift selector position is in P-range with the ignition switch ON or with the engine started.NOTE: After starting to inflate the tire, it takes a few seconds for the easy fill tire alert to function. ...

    Mac Key Writing
    Description When replacing around view monitor control unit, it is necessary to write MAC key to around view monitor control unit. Write MAC key to around view monitor control unit according to "MAC Key writing" procedure of "CONSULT Operation Manual". Refer to Work Procedure.CAUTION: During ...

    C1203-86 Abs Signal
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1203-86 ABS SYSTEM (Antilock brake system) Diagnosis condition Ignition switch: ON Nissan Ariya Vehicle running Signal Wheel speed signals ...