Nissan Rogue (T33) 2021-Present Service Manual: U214f-57 Mac Comm Error (bcm)

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Chassis Control :: Dtc/circuit Diagnosis / U214f-57 Mac Comm Error (bcm)

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
U214F 57 CAN communication error (BCM) Diagnosis condition —
Signal (terminal) —
Threshold MAC communication error.
Diagnosis delay time —

POSSIBLE CAUSE

  • Chassis control module used in vehicles is installed in the vehicle

  • Chassis control module

  • BCM

FAIL-SAFE

-

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “U2140-57” is displayed with DTC “U1327-52” or “U1327-54”, first perform the trouble diagnosis for DTC “U1327-52” or “U1327-54”.

Is DTC “U1327-52” or “U1327-54” detected?

YES>>

  • “U1327–52”: Refer to DTC Description.

  • “U1327–54”: Refer to DTC Description.

NO>>

GO TO 2.

CHECK MAC DIAGNOSIS

With CONSULT

  1. Ignition switch ON.

  2. Perform “MAC Diagnosis” mode of “CHASSIS CONTROL” using CONSULT.

Is DTC “U214F-57” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “U214F-57” is displayed with DTC “U1327-52” or “U1327-54”, first perform the trouble diagnosis for DTC “U1327-52” or “U1327-54”.

Is DTC “U1327-52” or “U1327-54” detected?

YES>>

  • “U1327–52”: Refer to DTC Description.

  • “U1327–54”: Refer to DTC Description.

NO>>

GO TO 2.

CHECK MAC DIAGNOSIS

With CONSULT

Perform “MAC Diagnosis” mode of “CHASSIS CONTROL” using CONSULT.

Is DTC "U214F-57" detected with "U2140-57", "U2141-57", "U2152-57", "U2165-57", "U2E52-57", "U2E65-57", and "U2E75-57" at the same time?

YES (all DTC codes are detected at the same time)>>

Replace the chassis control module. Refer to Removal and Installation.

NO (all DTC codes are not detected at the same time)>>

GO TO 3.

CHECK CAN COMMUNICATION SYSTEM

Check CAN communication system. Refer to Trouble Diagnosis Flow Chart.

>>

INSPECTION END

    U2143-87 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2143 87 CAN communication error (VCM) Diagnosis condition When ignition switch is ON. S...
    U214f-83 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U214F 83 CAN communication error (BCM) Diagnosis condition When ignition switch is ON. S...

    Other materials:

    Corrosion protection
    Most common factors contributing to vehicle corrosion Moisture-retaining dirt and debris build-up inside body cavities or seams. Paint or coating damage caused by gravel, small stones or minor collisions. Environmental factors influencing corrosion rate Moisture Sand, dirt and water accumulat ...

    Power Supply and Ground Circuit
    Ecm Diagnosis Procedure CHECK THE BATTERY CABLE Turn ignition switch OFF. Check the battery cable for tightening enough. NOTE: Check the continuity between the battery cable and the battery terminal. Is the inspection result normal? YES>> GO TO 2 ...

    Dtc/circuit Diagnosis. B2428-46 Automatic Back Door Control Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2428-46 Automatic back door control unit (Automatic back door control unit) Diagnosis condition All times Signal (terminal) — Threshold Automatic ...