Nissan Rogue (T33) 2021-Present Service Manual: U2118-87 Can Comm Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Driver Assistance System / Chassis Control :: Dtc/circuit Diagnosis / U2118-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms DTC detection condition
U2118 87 CAN communication error (Intelligent Key unit) Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold Not receiving from intelligent key unit.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • CAN communication system

  • Intelligent key unit

FAIL-SAFE

Normal control

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Ignition switch OFF to ON.

    CAUTION:

    Be sure to wait of 10 seconds after ignition switch OFF or ON.

  2. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U2118-87” detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Erase self-diagnosis result for “CHASSIS CONTROL”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “U2118-87” detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK INTELLIGENT KEY UNIT SYSTEM (1)

With CONSULT

  1. Erase self-diagnosis result for “INTELLIGENT KEY”.

  2. Ignition switch OFF and wait for 10 seconds or more.

  3. Ignition switch ON.

  4. Perform self-diagnosis for “INTELLIGENT KEY”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 3.

CHECK INTELLIGENT KEY UNIT SYSTEM (2)

  1. Ignition switch OFF.

  2. Disconnect intelligent key unit harness connector.

  3. Check intelligent key unit harness connector terminals (CAN communication line) for damage or loose connection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

ERASE SELF-DIAGNOSIS RESULT

With CONSULT

  1. Connect intelligent key unit harness connector.

  2. Erase self-diagnosis result for “CHASSIS CONTROL”.

  3. Ignition switch OFF and wait for 10 seconds or more.

>>

INSPECTION END

    U1327-54 Mac Key
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U1327 54 MAC key update Diagnosis condition — Signal (terminal) — Threshold MAC key ...
    U2140-57 Mac Comm Error (ecm)
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detection condition U2140 57 CAN communication error (ECM) Diagnosis condition — Signal (terminal) — Thr...

    Other materials:

    ProPILOT Assist displays and indicators
    Models with full-screen display Models with analog meter and color display ProPILOT Assist, ProPILOT Assist 1.1 ProPILOT activationAppears once the ProPILOT Assist system in your Nissan Rogue is activated. Vehicle ahead detection indicatorShows whether the system detects a vehicle ahead (only ...

    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check that the function operates normally according to the following conditions: Condition Value CONTRO ...

    Charge Air Cooler
    Exploded View Charge air cooler Charge air cooler Bracket 1 Turbocharger boost sensor (with intake air temperature sensor 2) O-ring Electronic throttle control actuator gasket Charge air cooler Bracket 2 Air inlet hose         To r ...