Nissan Rogue (T33) 2021-Present Service Manual: U1cad-02 Air Mix Door Motor 2

Nissan Rogue (T33) 2021-Present Service Manual / Ventilation, Heater & Air Conditioner :: Heater & Air Conditioning Control System / Automatic Air Conditioning :: Dtc/circuit Diagnosis / U1cad-02 Air Mix Door Motor 2

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
U1CAD-02

Air mix door motor 2

(Air mix door motor 2) 		Diagnosis condition Ignition switch ON
Signal (Terminal) LIN (door motor) signal
Threshold A/C amp. is not transmitting or receiving LIN communication with air mix door motor RH
Diagnosis delay time 2 second or more

POSSIBLE CAUSE

  • Harness and connector (air mix door motor RH circuit is open or shorted to ground)

  • Air mix door motor RH

  • A/C amp.

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Start the engine.

  2. Select “Self diagnosis result” mode of “HVAC”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK AIR MIX DOOR MOTOR RH POWER SUPPLY

  1. Ignition switch ON.

  2. Check voltage between air mix door motor RH harness connector and A/C amp. harness connector.

(+) (−) Voltage
Air mix door motor RH A/C amp.
Connector Terminal Connector Terminal
M140 1 M55 58 Battery voltage

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 4.

CHECK AIR MIX DOOR MOTOR RH GROUND CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect air mix door motor RH connector and A/C amp. connector.

  3. Check continuity between air mix door motor RH harness connector and A/C amp. harness connector.

    Air mix door motor RH A/C amp. Continuity
    Connector Terminal Connector Terminal
    M140 2 M54 27 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair harness or connector.

CHECK AIR MIX DOOR MOTOR RH LIN SIGNAL CIRCUIT

  1. Connect air mix door motor RH connector and A/C amp. connector.

  2. Ignition switch ON.

  3. Confirm output waveform between air mix door motor RH harness connector and A/C amp. harness connector with oscilloscope.

    (+) (−) Output waveform
    Air mix door motor RH A/C amp.
    Connector Terminal Connector Terminal
    M140 3 M55 58

Is the inspection result normal?

YES>>

Replace air mix door motor RH. Refer to Removal and Installation.

NO>>

GO TO 6.

CHECK AIR MIX DOOR MOTOR RH POWER SUPPLY CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect air mix door motor RH connector and A/C amp. connector.

  3. Check continuity between air mix door motor RH harness connector and A/C amp. harness connector.

    Air mix door motor RH A/C amp. Continuity
    Connector Terminal Connector Terminal
    M140 1 M54 1 Yes

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair harness or connector.

CHECK AIR MIX DOOR MOTOR RH POWER SUPPLY CIRCUIT FOR SHORT

  1. Disconnect following connectors.

    • Air mix door motor LH

    • Air mix door motor (rear)

    • Intake door motor

    • Mode door motor

  2. Check continuity between air mix door motor RH harness connector and ground.

    Air mix door motor RH (—) Continuity
    Connector Terminal
    M140 1 Ground No

Is the inspection result normal?

YES>>

Replace A/C amp. Refer to Removal and Installation.

NO>>

Repair harness or connector.

CHECK AIR MIX DOOR MOTOR RH LIN SIGNAL CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect air mix door motor RH connector and A/C amp. connector.

  3. Check continuity between air mix door motor RH harness connector and A/C amp. harness connector.

    Air mix door motor RH A/C amp. Continuity
    Connector Terminal Connector Terminal
    M140 3 M54 2 Yes

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair harness or connector.

CHECK AIR MIX DOOR MOTOR RH LIN SIGNAL CIRCUIT FOR SHORT

  1. Disconnect following connectors.

    • Air mix door motor LH

    • Air mix door motor (rear)

    • Intake door motor

    • Mode door motor

  2. Check continuity between air mix door motor RH harness connector and ground.

    Air mix door motor RH (—) Continuity
    Connector Terminal
    M140 3 Ground No

Is the inspection result normal?

YES>>

Replace A/C amp. Refer to Removal and Installation.

NO>>

Repair harness or connector.

    U1cac-02 Air Mix Door Motor 1
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1CAC-02 Air mix door motor 1 (Air mix door motor 1) Diagnos...
    U1cae-02 Rear Air Mix Door Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1CAE-02 Rear air mix door motor (Rear air mix door motor) D...

    Other materials:

    Dtc/circuit Diagnosis. Horn Function
    Component Function Check CHECK FUNCTION CONSULT Ignition switch OFF. Perform “Horn” in “Active test” mode of “IPDM E/R”. Check the horn operation. Test item Description Horn On Horn Sounds (for 20 ms.) Is the operation normal? YES>> Ins ...

    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check that the function operates normally according to the following conditions: Condition Value CONTRO ...

    Chassis Can Communication 4 Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the diagnostic CAN communication circuit normal? YES>> GO TO 2. NO>> Check and repair diagnostic CAN commu ...