Nissan Rogue (T33) 2021-Present Service Manual: U1cae-02 Rear Air Mix Door Motor

Nissan Rogue (T33) 2021-Present Service Manual / Ventilation, Heater & Air Conditioner :: Heater & Air Conditioning Control System / Automatic Air Conditioning :: Dtc/circuit Diagnosis / U1cae-02 Rear Air Mix Door Motor

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
U1CAE-02

Rear air mix door motor

(Rear air mix door motor) 		Diagnosis condition Ignition switch ON
Signal (Terminal) LIN (door motor) signal
Threshold A/C amp. is not transmitting or receiving LIN communication with air mix door motor (rear)
Diagnosis delay time 2 second or more

POSSIBLE CAUSE

  • Harness and connector [air mix door motor (rear) circuit is open or shorted to ground]

  • Air mix door motor (rear)

  • A/C amp.

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Start the engine.

  2. Select “Self diagnosis result” mode of “HVAC”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK AIR MIX DOOR MOTOR (REAR) POWER SUPPLY

  1. Ignition switch ON.

  2. Check voltage between air mix door motor (rear) harness connector and A/C amp. harness connector.

(+) (−) Voltage
Air mix door motor (rear) A/C amp.
Connector Terminal Connector Terminal
M151 1 M55 58 Battery voltage

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 4.

CHECK AIR MIX DOOR MOTOR (REAR) GROUND CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect air mix door motor (rear) connector and A/C amp. connector.

  3. Check continuity between air mix door motor (rear) harness connector and A/C amp. harness connector.

    Air mix door motor (rear) A/C amp. Continuity
    Connector Terminal Connector Terminal
    M151 2 M54 27 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair harness or connector.

CHECK AIR MIX DOOR MOTOR (REAR) LIN SIGNAL CIRCUIT

  1. Connect air mix door motor (rear) connector and A/C amp. connector.

  2. Ignition switch ON.

  3. Confirm output waveform between air mix door motor (rear) harness connector and A/C amp. harness connector with oscilloscope.

    (+) (−) Output waveform
    Air mix door motor (rear) A/C amp.
    Connector Terminal Connector Terminal
    M151 3 M55 58

Is the inspection result normal?

YES>>

Replace air mix door motor (rear). Refer to Removal and Installation.

NO>>

GO TO 6.

CHECK AIR MIX DOOR MOTOR (REAR) POWER SUPPLY CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect air mix door motor (rear) connector and A/C amp. connector.

  3. Check continuity between air mix door motor (rear) harness connector and A/C amp. harness connector.

    Air mix door motor (rear) A/C amp. Continuity
    Connector Terminal Connector Terminal
    M151 1 M54 1 Yes

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair harness or connector.

CHECK AIR MIX DOOR MOTOR (REAR) POWER SUPPLY CIRCUIT FOR SHORT

  1. Disconnect following connectors.

    • Air mix door motor LH

    • Air mix door motor RH

    • Intake door motor

    • Mode door motor

  2. Check continuity between air mix door motor (rear) harness connector and ground.

    Air mix door motor (rear) (—) Continuity
    Connector Terminal
    M151 1 Ground No

Is the inspection result normal?

YES>>

Replace A/C amp. Refer to Removal and Installation.

NO>>

Repair harness or connector.

CHECK AIR MIX DOOR MOTOR (REAR) LIN SIGNAL CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect air mix door motor (rear) connector and A/C amp. connector.

  3. Check continuity between air mix door motor (rear) harness connector and A/C amp. harness connector.

    Air mix door motor (rear) A/C amp. Continuity
    Connector Terminal Connector Terminal
    M151 3 M54 2 Yes

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair harness or connector.

CHECK AIR MIX DOOR MOTOR (REAR) LIN SIGNAL CIRCUIT FOR SHORT

  1. Disconnect following connectors.

    • Air mix door motor LH

    • Air mix door motor RH

    • Intake door motor

    • Mode door motor

  2. Check continuity between air mix door motor (rear) harness connector and ground.

    Air mix door motor (rear) (—) Continuity
    Connector Terminal
    M151 3 Ground No

Is the inspection result normal?

YES>>

Replace A/C amp. Refer to Removal and Installation.

NO>>

Repair harness or connector.

    U1cad-02 Air Mix Door Motor 2
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1CAD-02 Air mix door motor 2 (Air mix door motor 2) Diagnos...
    U1cb1-02 A/c Control 2 Communication
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U1CB1-02 A/C control 2 communication (Air conditioning contr...

    Other materials:

    Dtc/circuit Diagnosis. P161d-00 Immobilizer
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detecting condition P161D-00 IMMOBILIZER (Immobilizer) Diagnosis condition Ignition switch ON Signal (terminal) — Threshold When Intelligent Key unit detects an immob ...

    Main Line Between Lib 12v and M&a Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side). Harness connector B41 Harness con ...

    Towing load/specification
    WARNING The towing capacities in this manual are general guidelines. Actual safe towing capacity of your Nissan Rogue depends on factory or dealer-installed equipment, passenger load, and cargo weight. You must weigh both the vehicle and trailer as described to determine true towing capacity. Never ...