Nissan Rogue (T33) 2021-Present Service Manual: U00ac Lin Communication

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / U00ac Lin Communication

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
U00AC 00

USM-IBS LIN Communication Failure

(USM-IBS LIN Communication Failure ) 		Diagnosis condition Ignition switch ON
Signal LIN communication
Threshold ECM detects LIN communication error
Diagnosis delay time 12 seconds

POSSIBLE CAUSE

  • Harness or connectors (LIN communication circuit is open or shorted.)

  • IPDM E/R

  • 12V battery current sensor

FAIL-SAFE

Engine Control System

Not applicable

Stop/Start System

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Ignition switch OFF and wait at least 10 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V when ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Ignition switch ON and wait at least 2 seconds.

  2. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY CURRENT SENSOR INPUT SIGNAL CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between 12V battery current sensor harness connector and

    12V battery current sensor IPDM E/R Continuity
    Connector Terminal Connector Terminal
    E37 2 E120 37 Existed

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

CHECK 12V BATTERY CURRENT SENSOR

Check 12V battery current sensor. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace 12V battery current sensor. Refer to Removal and Installation.

    P34c8 Electric Intake Valve Timing Control Module
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P34C8 00 Camshaft position control module (Camshaft position con...
    U0101 Can Comm Circuit
    DTC Description DESCRIPTIONCAN (Controller Area Network) is a serial communication line for real time application. It is an on-Nissan Ariya vehicle multiplex communication line ...

    Other materials:

    C1f00-54 Hands Off Threshold Incomplete
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F00 54 CONTROL UNIT (Control unit) Diagnosis condition — Signal (terminal) — Threshold Steering Torque C ...

    Automatic Brake Hold. Symptom Diagnosis. Does Not Operate
    Does Not Operate Diagnosis Procedure Automatic brake hold function does not operate when the operating conditions are satisfied.PERFORM SELF-DIAGNOSIS (CHASSIS CONTROL MODULE) With CONSULT Perform self-diagnosis for “CHASSIS CONTROL”. Is DTC detected? YES>> Check the DTC. With ...

    Dtc/circuit Diagnosis. C161a-82 Abs System
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C161A 82 ABS system (Anti-lock braking system ) Diagnosis condition When ignition switch is ON. Signal (terminal) CAN communication signal Threshold ...