Nissan Rogue (T33) 2021-Present Service Manual: Steering Switch Signal a Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Information & Multimedia :: Meter, Warning Lamp & Indicator / Type a :: Dtc/circuit Diagnosis / Steering Switch Signal a Circuit

Component Function Check

CHECK COMBINATION METER INPUT SIGNAL

CONSULT

  1. Ignition switch ON.

  2. Select “Steering switch input” in “Data monitor” mode of “M&A”.

  3. Check that the function operates normally according to the following conditions:

Condition Value
CONTROL switch is pressed SW1
Jog dial is rotated to upward SW2
Jog dial is rotated to downward SW3
OK switch is pressed SW4
LEFT/BACK switch is pressed SW5
RIGHT switch is pressed SW6
VOL DOWN switch is pressed SW7
VOL UP switch is pressed SW8
TEL END switch is pressed SW9
VR/TEL switch is pressed SW10
SEEK DOWN switch is pressed SW11
SEEK UP switch is pressed SW12
Other than above NO INPUT

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

The steering switch has a built-in CPU. Details for refer to Steering Switch.

CHECK FUSE

Check that the fuse is not blown:

Unit Location Fuse No. Capacity
Steering switches Fuse block (J/B) 40 10 A

Is the fuse blown?

YES>>

Replace the blown fuse after repairing the affected circuit.

NO>>

GO TO 2.

CHECK STEERING SWITCH POWER SUPPLY CIRCUIT

  1. Ignition switch ON.

  2. Check voltage between spiral cable harness connector and ground.

    Terminals Ignition switch position

    Voltage

    (Approx.)
    (+) (−)
    Spiral cable Ground
    Connector Terminal
    M30 16 ACC or ON Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair harness or connector.

CHECK STEERING SWITCH GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect spiral cable harness connector.

  3. Check continuity between spiral cable harness connector and ground.

    Spiral cable Ground Continuity
    Connector Terminal
    M30 15 Yes

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair harness or connector.

CHECK STEERING SWITCH SIGNAL A CIRCUIT

  1. Disconnect combination meter harness connector.

  2. Check continuity between combination meter harness connector and spiral cable harness connector.

    Combination meter Spiral cable Continuity
    Connector Terminal Connector Terminal

    M73 (U.S.A. production)

    M77 (Japan production)     		33 M30 13 Yes

  3. Check continuity between combination meter harness connector and ground.

    Combination meter Ground Continuity
    Connector Terminal

    M73 (U.S.A. production)

    M77 (Japan production)     		33 No

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair harness or connector.

CHECK STEERING SWITCH SIGNAL GROUND CIRCUIT

  1. Check continuity between combination meter harness connector and spiral cable harness connector.

    Combination meter Spiral cable Continuity
    Connector Terminal Connector Terminal

    M73 (U.S.A. production)

    M77 (Japan production)     		34 M30 11 Yes

  2. Check continuity between combination meter harness connector and ground.

    Combination meter Ground Continuity
    Connector Terminal

    M73 (U.S.A. production)

    M77 (Japan production)     		34 No

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair harness or connector.

CHECK SPIRAL CABLE

  1. Disconnect spiral cable harness connectors.

  2. Check continuity between spiral cable harness connectors.

    Spiral cable Continuity
    Connector Terminal Connector Terminal
    M154 22 M30 16 Yes
    29 15
    27 13
    25 11

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Replace spiral cable. Refer to Removal and Installation.

CHECK STEERING SWITCH

Check steering switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace steering switches. Refer to Removal and Installation.

    Meter Speaker Signal Circuit
    Diagnosis Procedure CHECK METER SPEAKER CIRCUIT FOR OPEN Ignition switch OFF. Disconnect combination meter harness connector and meter speaker harness connector. Check the conti...
    Steering Switch Signal B Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL CONSULT Ignition switch ON. Select “Steering switch input” in “Data monitor” mode of “M&A”. Check t...

    Other materials:

    Dtc/circuit Diagnosis. Memory Indicator
    Component Function Check CHECK FUNCTION Push set switch. Check memory indicator operation. When driver seat position is already retained in memory : Illuminated for 5 seconds When driver seat position is not retained in memory : Illuminated for 0.5 second Is the ins ...

    C1f48-62 Abs/tcs/vdc System
    Without Propilot Assist 2.1 DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition   C1F48 62 ABS/TCS/VDC CIRC (Anti-lock braking system/Traction control system/Nissan Ariya Vehicle dynamics control system circuit) ...

    Dtc/circuit Diagnosis. U2141-87 Can Comm Circuit
    DTC Description DESCRIPTIONCAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Ariya vehicle is equipped ...