Nissan Rogue (T33) 2021-Present Service Manual: Power Supply and Ground Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Information & Multimedia :: Meter, Warning Lamp & Indicator / Type a :: Dtc/circuit Diagnosis / Power Supply and Ground Circuit

Combination Meter

Diagnosis Procedure

CHECK FUSES

Check that the following fuses are not blown:

Unit Location Fuse No. Capacity
Combination meter Fuse block (J/B) 29 5A
6 5A

Is the fuse blown?

YES>>

Replace the blown fuse after repairing the affected circuit.

NO>>

GO TO 2.

CHECK POWER SUPPLY CIRCUIT

  1. Disconnect combination meter harness connector.

  2. Check voltage between combination meter harness connector and ground.

    (+) (–) Ignition switch position
    Combination meter
    Connector Terminal OFF ON START

    M73 (U.S.A. production)

    M77 (Japan production)     		5 Ground Battery voltage Battery voltage Battery voltage
    6 0V Battery voltage Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness or connector.

CHECK GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Check continuity between combination meter harness connector and ground.

    Combination meter Ground Continuity
    Connector Terminal

    M73 (U.S.A. production)

    M77 (Japan production)     		7 Yes

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair harness or connector.

Head up Display Unit

Diagnosis Procedure

CHECK FUSE

  1. Check that the following fuse is not blown:

    Unit Location Fuse No. Capacity
    Head up display unit Fuse block (J/B) 48 5A

Is the fuse blown?

YES>>

Replace the blown fuse after repairing the affected circuit.

NO>>

GO TO 2.

CHECK POWER SUPPLY CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect Head Up Display unit harness connector.

  3. Ignition switch ON.

  4. Check the voltage between Head Up Display unit harness connector and ground.

    (+) (–) Ignition switch position
    Head up display unit
    Connector Terminal OFF ON ACC
    M110 9 Ground 0V Battery voltage Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness or connector.

CHECK GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Check the continuity between Head Up Display unit harness connector and ground.

    Head Up Display unit Ground Continuity
    Connector Terminal
    M110 16 Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Repair or replace harness or connector.

    Head up Display Unit
    B22a0-46 Head up Display Unit DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis contents) DTC detection condition B22A0-46 Control unit (Contro...
    Meter Speaker Signal Circuit
    Diagnosis Procedure CHECK METER SPEAKER CIRCUIT FOR OPEN Ignition switch OFF. Disconnect combination meter harness connector and meter speaker harness connector. Check the conti...

    Other materials:

    Preparation
    Special Service Tool The actual shapes of TechMate tools may differ from those of special service tools illustrated here. Tool number (TechMate No.) Tool name   Description (NI-39570) Chassis ear Locates the noise (NI-50397) NISSAN Squeak and Rattle Kit Repairs ...

    Tire chains
    WARNING If tire chains are used on the Nissan Rogue, ensure they provide adequate clearance from suspension and body components. Incorrect chain selection or improper installation can cause damage to brakes, suspension or other components, risking a crash. Use only the recommended chains or an app ...

    Lane Change Assist
    Basic information Lane Change Assist is a feature of ProPILOT Assist 2.1 on the Nissan Rogue. Read the entire ProPILOT Assist section before using this system, including how to operate it and how to interpret the display. When ProPILOT Assist is active and the status indicator A is illuminated in ...