Nissan Rogue (T33) 2021-Present Service Manual: P268a Fuel Injector Calibration

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P268a Fuel Injector Calibration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P268A 00

Fuel injector calibration

(Fuel Injector Calibration Not Learned/Programmed) 		Diagnosis condition Fuel injector offset learning in progress
Signal (terminal) —
Threshold When the injector offset learning cannot be done for 36 seconds or longer.
Diagnosis delay time 36 seconds

POSSIBLE CAUSE

  • ECM

  • Fuel injector

  • Fuel rail pressure sensor

  • High pressure fuel pump

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

NOTE:

ECM does not control the accelerator pedal releasing speed.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited.

When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P268A is displayed with other DTC, first perform the confirmation procedure (trouble diagnosis) for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer DTC Index.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Select “Fuel injector offset learning” in “WORK SUPPORT” mode of “ENGINE” using CONSULT.

  2. Check the DTC.

Is DTC P268A detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P268A is displayed with other DTC, first perform the confirmation procedure (trouble diagnosis) for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer DTC Index.

NO>>

GO TO 2.

CHECK FUEL RAIL PRESSURE SENSOR

Check fuel rail pressure sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK FUEL INJECTOR

Check fuel injector. Refer to Component Function Check.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK HIGH PRESSURE FUEL PUMP

Check high pressure fuel pump. Refer to Component Function Check.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

REPLACE ECM

  1. Replace ECM. Refer to ECM : Removal & Installation.

  2. Perform DTC confirmation procedure again. Refer to DTC Description.

  3. Check the DTC.

Is the DTC P268A displayed again?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

INSPECTION END

    P2619 Crankshaft Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2619 00 Crankshaft position signal (Crankshaft position signal ...
    P26a3 Multi-Way Control Valve Motor
    DTC Description DTC DETECTION LOGICNOTE: If DTC P26A3 is displayed with DTC P26A5, P26A6, and/or P26A7 first perform the trouble diagnosis for DTC P26A5, P26A6, and/or P26A7. Re...

    Other materials:

    Dtc/circuit Diagnosis. Power Supply and Ground Circuit
    Diagnosis Procedure CHECK FUSE Ignition switch OFF. Check that the following fuses are not blown (open): With type A meter Unit Location Fuse No. Capacity 28 Battery power supply 30 5 A 135 Battery power supply (door lock 1) 12 10 A 136 Battery power ...

    B20d4-11 Tail Lamp Lh Pwr Sply Circ
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition B20D4–11 TAIL LAMP LH PWR SPLY CIRC (Tail lamp left hand power supply circuit) [CIRCUIT SHORT TO GROUND] Diagnosis condition When the parking lamp, license pla ...

    System Description. Component Parts. Wiper and Washer System
    Wiper and Washer System Component Parts Location Component Parts Location A. View with washer tank removed from Nissan Ariya vehicle (for USA) B. View with washer tank removed from vehicle C. Behind LH side of front fascia assembly (view with front fascia assembly) removed No. ...