Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Power Supply and Ground Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Body Control System / Dtc/circuit Diagnosis :: Power Supply and Ground Circuit

Diagnosis Procedure

CHECK FUSE

  1. Ignition switch OFF.

  2. Check that the following fuses are not blown (open):

    With type A meter
    Unit Location Fuse No. Capacity
    28 Battery power supply 30 5 A
    135 Battery power supply (door lock 1) 12 10 A
    136 Battery power supply 15 5 A
    137 Battery power supply (turn signal lamp) 58 15 A
    138 Battery power supply (rear wiper) 56 15 A
    142 Battery power supply (stop lamp) 21 10 A
    144 Battery power supply (door lock 2) 14 10 A
    With type B meter
    Unit Location Fuse No. Capacity
    7 Battery power supply 30 5 A
    133 15 5 A
    135 Battery power supply (front door lock) 12 10 A
    136 Battery power supply (turn signal lamp) 58 15 A
    138 Battery power supply (rear wiper) 56 15 A
    139 Battery power supply (stop lamp) 21 10 A
    144 Battery power supply (rear door lock) 14 10 A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK POWER SUPPLY CIRCUIT

  1. Disconnect BCM connectors.

  2. Check voltage between BCM harness connectors and ground.

    With type A meter
    + − Voltage
    BCM
    Connector Terminal
    M51 28 Ground Battery voltage
    B124 135
    136
    137
    138
    142
    144
    With type B meter
    + − Voltage
    BCM
    Connector Terminal
    M18 7 Ground Battery voltage
    B23 133
    135
    136
    138
    139
    144

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair harness or connector.

CHECK GROUND CIRCUIT

Check continuity between BCM harness connector and ground.

With type A meter
BCM — Continuity
Connector Terminal
B124 132 Ground Yes
140
With type B meter
BCM — Continuity
Connector Terminal
B23 129 Ground Yes
137

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Repair harness or connector.

    Dtc/circuit Diagnosis. U3d01-51 Fota
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition U3D01-51 FOTA (FOTA) Diagnosis condition Ignition switch is ...
    Dtc/circuit Diagnosis. Combination Switch Input Circuit
    Diagnosis Procedure CHECK INPUT CIRCUIT Ignition switch OFF. Disconnect combination switch connector. Ignition switch ON. Check voltage between combination switch harness connec...

    Other materials:

    P0097 Iat Sensor 2
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0097 00 IAT SENSOR 2 B1 (Intake air temperature sensor 2 circuit low bank 1) Diagnosis condition — Signal (terminal) — Threshold ECM dete ...

    Periodic Maintenance. Front Suspension Assembly
    Inspection COMPONENT PARTCheck the front suspension for the following: Check each component for looseness or play. Inspect each component for abnormal wear or damage. Ball Joint Axial End PlayWARNING: When moving the front tires up and down by hand, place a jack (A) at the rear floor ...

    Dtc/circuit Diagnosis. Back Door Request Switch
    Component Inspection CHECK BACK DOOR REQUEST SWITCH Ignition switch OFF. Disconnect back door opener switch connector. Check back door opener switch terminals. Back door opener switch Condition Continuity Terminal 3 4 Back door request switch Pressed Yes ...