Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Combination Switch Input Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Body Control System / Dtc/circuit Diagnosis :: Combination Switch Input Circuit

Diagnosis Procedure

CHECK INPUT CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect combination switch connector.

  3. Ignition switch ON.

  4. Check voltage between combination switch harness connector and ground.

    Switch signal + − Voltage
    Combination switch
    Connector Terminal
    Input 1 M28 1 Ground Battery voltage
    Input 2 3
    Input 3 4
    Input 4 6
    Input 5 8
    Input 6 13

Is the inspection result normal?

Yes>>

Replace combination switch. Refer to Removal and Installation.

No>>

GO TO 2.

CHECK INPUT CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect BCM connector.

  3. Check continuity between BCM harness connector and combination switch harness connector.

    With type A meter
    Switch signal BCM Combination switch Continuity
    Connector Terminal Connector Terminal
    Input 1 M58 58 M28 1 Yes
    Input 2 49 3
    Input 3 50 4
    Input 4 57 6
    Input 5 51 8
    Input 6 54 13
    With type B meter
    Switch signal BCM Combination switch Continuity
    Connector Terminal Connector Terminal
    Input 1 M19 67 M28 1 Yes
    Input 2 68 3
    Input 3 69 4
    Input 4 70 6
    Input 5 71 8
    Input 6 72 13

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair harness or connector.

CHECK INPUT CIRCUIT FOR SHORT

Check continuity between BCM harness connector and ground.

With type A meter
Switch signal BCM — Continuity
Connector Terminal
Input 1 M58 58 Ground No
Input 2 49
Input 3 50
Input 4 57
Input 5 51
Input 6 54
With type B meter
Switch signal BCM — Continuity
Connector Terminal
Input 1 M19 67 Ground No
Input 2 68
Input 3 69
Input 4 70
Input 5 71
Input 6 72

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair harness or connector.

    Dtc/circuit Diagnosis. Power Supply and Ground Circuit
    Diagnosis Procedure CHECK FUSE Ignition switch OFF. Check that the following fuses are not blown (open): With type A meter Unit Location Fuse No. Capacity 28 Battery power suppl...
    Dtc/circuit Diagnosis. Combination Switch Output Circuit
    Diagnosis Procedure CHECK OUTPUT CIRCUIT Ignition switch ON. Turn ON any switch in the system that is malfunctioning. Check duty ratios between BCM harness connector and ground ...

    Other materials:

    Limites du système RAB
    AVERTISSEMENT Les limites du système de freinage automatique arrière (RAB) du Nissan Rogue sont décrites ci-dessous. Le non-respect des instructions et avertissements relatifs à l’utilisation correcte du système RAB peut entraîner des blessures graves, voire mortelles. Le conducteur doit to ...

    Front Blower Motor
    Diagnosis Procedure CHECK FUSE Ignition switch OFF. Check that the following fusible link are not blown (open). Unit Location Fuse No. Capacity Front blower motor Fuse block (J/B) LL 40 A Is the fuses blown (open)? YES>> Replace the blown (open) fusib ...

    Tableau de bord
    Le tableau de bord du Nissan Rogue regroupe l’affichage des informations essentielles et les commandes de climatisation/infodivertissement. Pour une utilisation sûre, réglez les fonctions principales à l’arrêt, puis gardez votre attention sur la route. Bouche d'aération latérale : ...