Nissan Rogue (T33) 2021-Present Service Manual: P2619 Crankshaft Position Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P2619 Crankshaft Position Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P2619 00

Crankshaft position signal

(Crankshaft position signal output circuit high) 		Diagnosis condition Engine running at idle
Signal (terminal) Crankshaft position sensor signal for electric intake valve timing control
Threshold The crankshaft position sensor signal edge count is more than 18 counts per one camshaft rotation
Diagnosis delay time 1 second

POSSIBLE CAUSE

Harness or connectors (Crankshaft position sensor signal circuit for electric intake valve timing control is open or shorted.)

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Idle speed control Stops feedback control of idle speed and controls with specified speed.
Recovery speed control at decelerating Stops recovery speed control by the fuel cut at decelerating and controls with specified speed.
Idle neutral control Stops idle neutral control.

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited.

When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P2619 is displayed with DTC P0335, first perform the confirmation procedure (trouble diagnosis) for DTC P0335.

Is DTC P0335 detected?

YES>>

Perform diagnosis of applicable. DTC P0335: Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and wait at least 5 seconds.

  2. Check 1st trip DTC.

Is DTC P2619 detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P2619 is displayed with DTC P0335, first perform the confirmation procedure (trouble diagnosis) for DTC P0335.

Is DTC P0335 detected?

YES>>

Perform diagnosis of applicable. DTC P0335: Refer to DTC Description.

NO>>

GO TO 2.

CHECK CRANKSHAFT POSITION (CKP) SENSOR SIGNAL CIRCUIT FOR ELECTRIC INTAKE VALVE TIMING CONTROL

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector and electric intake valve timing control module harness connector.

  3. Check the continuity between ECM harness connector and electric intake valve timing control module harness connector.

    ECM Electric intake valve timing control module Continuity
    Connector Terminal Connector Terminal
    F71 88 F113 18 Existed

  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace error-detected parts.

    P2618 Crankshaft Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2618 00 Crankshaft position signal (Crankshaft position signal ...
    P268a Fuel Injector Calibration
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition P268A 00 Fuel injector calibration (Fuel Injector Calibratio...

    Other materials:

    Symptom Diagnosis. Panic Alarm Function Does Not Operate
    Description Panic alarm does not operate when press the PANIC ALARM button of Intelligent Key. Diagnosis Procedure CHECK INTELLIGENT KEY SYSTEM (REMOTE KEYLESS ENTRY FUNCTION) Press the LOCK button of Intelligent Key. Are all doors LOCKED? YES>> GO TO 2. NO>> Check Intelligent ...

    System Description. Component Parts. Srs Air Bag Control System
    Srs Air Bag Control System Component Parts Location 1. Rear side air bag module 2. Curtain air bag module 3. Front side air bag module 4. Knee air bag module 5. Passenger air bag module 6. Front seat belt buckle switch 7. BCM (Body Control Module) Refe ...

    Accelerator Pedal Position Sensor
    Component Inspection CHECK ACCELERATOR PEDAL POSITION SENSOR Turn ignition switch OFF. Reconnect all harness connectors disconnected. Turn ignition switch ON. Check the voltage between ECM harness connector terminals as per the following condition. ECM Condition Voltage (A ...