Nissan Rogue (T33) 2021-Present Service Manual: P2482 Exhaust Gas Temperature Sensor
DTC Description
DTC DETECTION LOGIC
| DTC |
CONSULT screen terms (Trouble diagnosis content) |
DTC detection condition | ||
| P2482 | 00 |
Exhaust gas temp sensor bank 1 (Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 5) |
Diagnosis condition | Ignition switch ON |
| Signal | — | |||
| Threshold | An excessively high voltage from the exhaust gas temperature sensor is sent to the ECM. | |||
| Diagnosis delay time | 5 seconds | |||
POSSIBLE CAUSE
-
Exhaust gas temperature sensor
-
Harness or connectors
(Exhaust gas temperature sensor circuit is open.)
FAIL-SAFE
Not applicable
DTC CONFIRMATION PROCEDURE
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
-
Turn ignition switch OFF and wait at least 10 seconds.
-
Turn ignition switch ON.
-
Turn ignition switch OFF and wait at least 10 seconds.
>>
GO TO 2.
PERFORM DTC CONFIRMATION PROCEDURE
-
Start the engine.
-
Let engine idle for 1 minutes.
-
Check the DTC.
Is the DTC detected?
YES>>Proceed to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK EXHAUST GAS TEMPERATURE SENSOR POWER SUPPLY
-
Ignition switch OFF.
-
Disconnect exhaust gas temperature sensor harness connector.
-
Ignition switch ON.
-
Check the voltage between exhaust gas temperature sensor harness connector and ground.
+ − Voltage
(Approx.)Exhaust gas temperature sensor Connector Terminal E26 1 Ground 5 V
Is the inspection result normal?
YES>>GO TO 2.
NO>>GO TO 3.
CHECK EXHAUST GAS TEMPERATURE SENSOR GROUND CIRCUIT
-
Ignition switch OFF.
-
Disconnect ECM harness connector.
-
Check the continuity between exhaust gas temperature sensor harness connector and ECM harness connector.
Exhaust gas temperature sensor ECM Continuity Connector Terminal Connector Terminal E26 2 F71 99 Existed -
Also check harness for short to power.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace error-detected parts.
CHECK EXHAUST GAS TEMPERATURE SENSOR INPUT SIGNAL CIRCUIT
-
Check the continuity between exhaust gas temperature sensor harness connector and ECM harness connector.
Exhaust gas temperature sensor ECM Continuity Connector Terminal Connector Terminal E26 1 F71 113 Existed -
Also check harness for short to ground and to power.
Is the inspection result normal?
YES>>GO TO 4.
NO>>Repair or replace error-detected parts.
CHECK EXHAUST GAS TEMPERATURE SENSOR
Check the exhaust gas temperature sensor. Refer to Component Inspection.
Is the inspection result normal?
YES>>Check intermittent incident. Refer to Intermittent Incident.
NO>>Replace exhaust gas temperature sensor. Refer to Component Parts Location.
Other materials:
Limites du système de détecteur de collision frontale intelligent
Illustration A
Illustration B
Illustration C
Illustration D
AVERTISSEMENT
Les limites du système de détecteur de collision frontale intelligent du Nissan Rogue sont décrites ci-dessous. Le non-respect de ces limites lors de la conduite peut entraîner des blessures gr ...
P155e Generator Voltage
DTC Description
DTC DETECTION LOGIC DTC
CONSULT screen terms
(Trouble diagnosis content) DTC detection condition
P155E
00
GENERATOR VOLTAGE
(GENERATOR VOLTAGE)
Diagnosis condition
Ignition switch ON
Signal (terminal)
Power supply
Threshold
Battery voltage measur ...
Régulateur de vitesse
Informations de base
Fonction de RES+
Fonction de SET-
Touche CANCEL
Commande marche/arrêt (ON/OFF)
de régulateur de vitesse
AVERTISSEMENT
Respectez toujours les limitations de vitesse en vigueur et ne réglez jamais la vitesse du régulateur au-delà des limites autorisées ...
