Nissan Rogue (T33) 2021-Present Service Manual: P2481 Exhaust Gas Temperature Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P2481 Exhaust Gas Temperature Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P2481 00

Exhaust gas temp sensor bank 1

(Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 5) 		Diagnosis condition Ignition switch ON
Signal —
Threshold An excessively low voltage from the exhaust gas temperature sensor is sent to the ECM.
Diagnosis delay time 5 seconds

POSSIBLE CAUSE

  • Exhaust gas temperature sensor

  • Harness or connectors

    (Exhaust gas temperature sensor circuit is open.)

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Let engine idle for 1 minutes.

  3. Check the DTC.

Is the DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK EXHAUST GAS TEMPERATURE SENSOR POWER SUPPLY

  1. Ignition switch OFF.

  2. Disconnect exhaust gas temperature sensor harness connector.

  3. Ignition switch ON.

  4. Check the voltage between exhaust gas temperature sensor harness connector and ground.

    + −

    Voltage

    (Approx.)
    Exhaust gas temperature sensor
    Connector Terminal
    E26 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 3.

CHECK EXHAUST GAS TEMPERATURE SENSOR GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between exhaust gas temperature sensor harness connector and ECM harness connector.

    Exhaust gas temperature sensor ECM Continuity
    Connector Terminal Connector Terminal
    E26 2 F71 99 Existed

  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK EXHAUST GAS TEMPERATURE SENSOR INPUT SIGNAL CIRCUIT

  1. Check the continuity between exhaust gas temperature sensor harness connector and ECM harness connector.

    Exhaust gas temperature sensor ECM Continuity
    Connector Terminal Connector Terminal
    E26 1 F71 113 Existed

  2. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK EXHAUST GAS TEMPERATURE SENSOR

Check the exhaust gas temperature sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace exhaust gas temperature sensor. Refer to Component Parts Location.

    P2480 Exhaust Gas Temperature Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2480 00 Exhaust gas temp sensor bank 1 (Exhaust Gas Temperature...
    P2482 Exhaust Gas Temperature Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2482 00 Exhaust gas temp sensor bank 1 (Exhaust Gas Temperature...

    Other materials:

    Transfer: Ty92a. Removal and Installation
    Transfer Oil Temperature Sensor Kr15ddt Exploded View Transfer oil temperature sensor Gasket Transfer assembly : N·m (kg-m, ft-lb) : Always replace after every disassembly. Removal and Installation REMOVALRemove engine under cover. Refer to Exploded View. Drain the ...

    Service After Replacing or Removing Engine Parts
    Description X: Applicable Part name Service performed Required service Reference Replacement Removal   ECM X — Additional service when replacing ECM Work Procedure Fuel injector offset learning Work Procedure Turbocharger wastegate control solenoid valve d ...

    B20c8-14 Ecv (electrical Control Valve)
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B20C8–14 Compressor (ECV) [Compressor (electrical control valve) [CIRC SHORT TO GRND OR OPEN] Diagnosis condition When A/C switch is ON Signal (Terminal) ...