Nissan Rogue (T33) 2021-Present Service Manual: P2480 Exhaust Gas Temperature Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P2480 Exhaust Gas Temperature Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P2480 00

Exhaust gas temp sensor bank 1

(Exhaust Gas Temperature sensor Circuit/Open Bank 1 Sensor 5) 		Diagnosis condition Ignition switch ON
Signal —
Threshold ECM detects exhaust gas temperature sensor circuit is shorted.
Diagnosis delay time 5 seconds

POSSIBLE CAUSE

  • Exhaust gas temperature sensor

  • Harness or connectors

    (Exhaust gas temperature sensor circuit is short.)

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 5 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK EXHAUST GAS TEMPERATURE SENSOR POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect exhaust gas temperature sensor harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between exhaust gas temperature sensor harness connector and ground.

    + −

    Voltage

    (Approx.)
    Exhaust gas temperature sensor
    Connector Terminal
    E26 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 3.

CHECK EXHAUST GAS TEMPERATURE SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between exhaust gas temperature sensor harness connector and ECM harness connector.

    + − Continuity
    Exhaust gas temperature sensor ECM
    Connector Terminal Connector Terminal
    E26 2 F71 99 Existed

  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK EXHAUST GAS TEMPERATURE SENSOR INPUT SIGNAL CIRCUIT

  1. Check the continuity between exhaust gas temperature sensor harness connector and ECM harness connector.

    + − Continuity
    Exhaust gas temperature sensor ECM
    Connector Terminal Connector Terminal
    E26 1 F71 113 Existed

  2. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK EXHAUST GAS TEMPERATURE SENSOR

Check the exhaust gas temperature sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace exhaust gas temperature sensor. Refer to Component Parts Location.

    P2297 Air Fuel Ratio Sensor 1
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2297 00 O2 SENSOR 1 B1 (O2 Sensor Out of Range During Decelerat...
    P2481 Exhaust Gas Temperature Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2481 00 Exhaust gas temp sensor bank 1 (Exhaust Gas Temperature...

    Other materials:

    Dtc/circuit Diagnosis. Door Lock Actuator
    Front Lh Diagnosis Procedure CHECK DOOR LOCK ACTUATOR INPUT SIGNAL Ignition switch OFF. Disconnect front door lock assembly LH connector. Check voltage between front door lock assembly LH harness connector and ground. (+) (–) Condition Voltage (Approx.) Front door lock a ...

    Symptom Diagnosis. Moonroof Does Not Operate Properly
    Description Moonroof does not operate normally. Moonroof tilt up/down, open/close does not operate. Moonroof tilt up/down, open/close operation is slow. Judder occurs during open/close operation of moonroof. Diagnosis Procedure CHECK MOONROOF UNIT ASSEMBLY Check the following it ...

    Removal and Installation. Steering Column
    Exploded View Steering column assembly Steering shaft lower cover Clip : N·m (kg-m, ft-lb) : Always replace after every disassembly. Removal and Installation REMOVALCAUTION: Do not cause impact to steering column or shaft during removal or installation. ...