Nissan Rogue (T33) 2021-Present Service Manual: P210b Admission Valve Motor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P210b Admission Valve Motor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P210B 00

Throttle actuator B control motor

(Throttle Actuator "B" Control Motor Circuit Range/Performance) 		Diagnosis condition IGN ON
Signal (terminal) ADM valve signal
Threshold ADM valve control function does not operate properly
Diagnosis delay time 1 second

POSSIBLE CAUSE

  • Harness or connectors (ADM valve circuit is open or shorted.)

  • ADM valve

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Idle speed control Stops feedback control of idle speed and controls with specified speed.
Recovery speed control at decelerating Stops recovery speed control by the fuel cut at decelerating and controls with specified speed.
Idle neutral control Stops idle neutral control.

Stop/Start System

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 2 seconds.

  2. Start engine and let it idle for 5 seconds.

  3. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ADM VALVE VISUALLY

Check if foreign matter is caught between the ADM valve.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Remove the foreign matter and clean the ADM valve inside.

CHECK ADM VALVE POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect ADM valve harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between ADM valve harness connector and ground.

    + −

    Voltage

    (Approx.)
    ADM valve
    Connector Terminal
    F93 5 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK ADM VALVE POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between ADM valve harness connector and ECM harness connector.

    + − Continuity
    ADM valve ECM
    Connector Terminal Connector Terminal
    F93 5 F71 84 Existed

  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK ADM VALVE GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between ADM valve harness connector and ECM harness connector.

    + − Continuity
    ADM valve ECM
    Connector Terminal Connector Terminal
    F93 4 F71 107 Existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK ADM VALVE MOTOR CIRCUIT

  1. Check the continuity between ADM valve harness connector and ECM harness connector.

    + − Continuity
    ADM valve ECM
    Connector Terminal Connector Terminal
    F93 1 F71 121 Existed
    2 122

  2. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts.

CHECK ADM VALVE

Check the ADM valve. Refer to Component Inspection.

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace ADM valve. Refer to Removal and Installation.

    P2103 Throttle Control Motor Relay
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2103 00 ETC MOT PWR-B1 (Throttle actuator “A” control motor...
    P2119 Electric Throttle Control Actuator
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2119 00 ETC ACTR-B1 (Throttle Actuator "A" Control Throttle Bod...

    Other materials:

    Basic Inspection. Consult/gst Checking System
    Description When CONSULT/GST is connected with a data link connector equipped on the Nissan Ariya vehicle side, it will communicate with the control unit equipped in the vehicle and then enable various kinds of diagnostic tests. : Instrument lower panel Refer to CONSULT S ...

    Limites du système MOD
    AVERTISSEMENT Les limites du système de détection d’objets en mouvement (MOD) du Nissan Rogue sont décrites ci-dessous. Le non-respect de ces limites pendant la conduite ou les manœuvres peut entraîner des blessures graves, voire mortelles. Le système MOD constitue une aide à la conduite e ...

    C1220-54 Incomplete Air Bleeding
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detecting condition C1220-54 INCOMP AIR BLEEDING (Incomplete air bleeding) Diagnosis condition Ignition switch: ON Signal — Threshold Air bleeding of electro-hydraulic co ...