Nissan Rogue (T33) 2021-Present Service Manual: P2103 Throttle Control Motor Relay

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P2103 Throttle Control Motor Relay

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P2103 00

ETC MOT PWR-B1

(Throttle actuator “A” control motor circuit high) 		Diagnosis condition Ignition switch ON
Signal (terminal) Throttle control motor relay signal
Threshold ECM detect the throttle control motor relay is stuck ON
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (Throttle control motor relay circuit is open.)

  • Throttle control motor relay

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 1 second.

  2. Check DTC.

Is DTC detected?

YES>>

DTC Diagnosis Procedure

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY

  1. Turn ignition switch ON.

  2. Check the voltage between ECM harness connectors.

    + −

    Voltage

    (Approx.)
    ECM
    Connector Terminal Connector Terminal
    F72 5 E21 160 Battery voltage
    E21 153

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Disconnect IPDM E/R harness connector.

  4. Check the continuity between ECM harness connector and IPDM E/R harness connector.

    ECM IPDM E/R Continuity
    Connector Terminal Connector Terminal
    F72 5 F35 73 Existed
    E21 153

  5. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace malfunctioning part.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL

  1. Turn ignition switch OFF.

  2. Check the voltage between ECM harness connectors.

    + − Condition

    Voltage

    (Approx.)
    ECM
    Connector Terminal Connector Terminal
    F72 24 E21 160 Ignition switch OFF 0 V
    ON Battery voltage

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 4.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Disconnect IPDM E/R harness connector.

  4. Check the continuity between ECM harness connector and IPDM E/R harness connector.

    ECM IPDM E/R Continuity
    Connector Terminal Connector Terminal
    F72 24 F42 93 Existed

  5. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace malfunctioning part.

    P2101 Electric Throttle Control Function
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2101 00 ETC FNCTN/CIRC-B1 (Throttle actuator “A” control mo...
    P210b Admission Valve Motor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P210B 00 Throttle actuator B control motor (Throttle Actuator "B...

    Other materials:

    P10c8 Internal Control Module Fuel Injector
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P10C8 00 Cylinder1 injector A (Cylinder1 injector A) Diagnosis condition — Signal (terminal) — Threshold Injector driver unit is malfu ...

    Fuel Injector and Fuel Tube
    Exploded View Fuel rail pressure sensor High pressure fuel rail insulator High pressure fuel rail O-ring (black) Support disc Fuel injector Decoupling element Valve seat Retaining ring spring Holding down appliance Stud bolt     ...

    Main Line Between Hvac and a-Bag Circuit
    Diagnosis Procedure CHECK HARNESS CONTINUITY (OPEN CIRCUIT) Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Disconnect the following harness connectors. A/C amp. Harness connectors M31 and E152 Check the continuity between the ...