Nissan Rogue (T33) 2021-Present Service Manual: P11ab Vcr Control Module Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P11ab Vcr Control Module Circuit

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P11AB 00

VCR control module circuit

(Variable compression ratio control module circuit) 		Diagnosis condition Engine running at idle
Signal (terminal) —
Threshold

  • VCR actuator

  • Malfunction in VCR control module processor
Diagnosis delay time —

POSSIBLE CAUSE

  • VCR control module

  • VCR actuator

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Check 1st trip DTC.

Is DTC P11AB detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

GO TO 2.

CHECK VCR ACTUATOR

With CONSULT

  1. On CONSULT screen, select “ENGINE”>>“Active Test”>>“VCR system”.

Is DTC P11AB detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK VCR MOTOR

  1. Turn ignition switch OFF.

  2. Disconnect VCR control module harness connector.

  3. Check the continuity between VCR control module harness connectors.

VCR control module Continuity
Terminal
4 2 Existed
3
2 3

Is the inspection result normal?

YES>>

Replace VCR control module. Refer to VCR CONTROL MODULE : Removal & Installation.

NO>>

GO TO 2.

CHECK VCR MOTOR CIRCUIT

  1. Disconnect VCR motor harness connector.

  2. Check the continuity between VCR control module harness connectors and VCR motor harness connector.

    VCR control module VCR motor Continuity
    Connector Terminal Connector Terminal
    F108 2 F107 1 Existed
    3 2
    4 3

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK VCR MOTOR

Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace malfunctioning parts.

    P11aa Vcr Position Learning
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11AA 00 VCR position learning (Variable compression ratio posit...
    P11ac Vcr Shaft 2 Rotation Angle Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11AC 00 VCR shaft 2 rotation angle sensor (Variable compression...

    Other materials:

    Illumination Control Switch Signal Circuit
    Component Function Check CHECK COMBINATION METER INPUT SIGNAL Ignition switch ON. Measure voltage between the following terminals of the combination meter. Combination meter Condition Voltage (Approx.) Connector Terminals (+) (−) M73 (U.S.A. production) ...

    Hazard warning flasher switch
    Press the hazard warning flasher switch to alert other drivers when you must stop or park under emergency conditions. All turn signal lights will flash simultaneously. WARNING If you must stop for an emergency, move the vehicle well off the roadway to avoid creating a hazard. Do not use the ...

    Egr Volume Control Valve
    Component Inspection CHECK EGR VOLUME CONTROL VALVE-1 With CONSULT Ignition switch ON (engine stopped). Perform “EGR CONTROL VALVE” in “ACTIVE TEST” mode of “ENGINE” using CONSULT. Operate “Up” or “Down”, set “EGR VALVE POSITION” to 0 deg, and check value “ ...