Nissan Rogue (T33) 2021-Present Service Manual: P11a8 Vcr Target Angle

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P11a8 Vcr Target Angle

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P11A8 00

VCR target angle

(Variable compression ratio target angle) 		Diagnosis condition

  • Engine running at idle

  • Engine speed : 4,500 rpm or more
Signal (terminal) —
Threshold There is a gap between angle of target and phase-control angle degree (High compression ratio)
Diagnosis delay time 110 seconds or more

POSSIBLE CAUSE

  • VCR actuator

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC P11A8 is displayed with the following DTC, perform the confirmation procedure (trouble diagnosis) for the applicable DTC.

Is DTC P11A0, P11A1, P11A2, P11A3 P11A4, P11A6, P11A7, P11AB, P11AC, P11AD, P11AE or P11AF detected?

YES>>

Perform diagnosis of applicable.

  • DTC P11A0: DTC Description.

  • DTC P11A1: DTC Description.

  • DTC P11A2: DTC Description.

  • DTC P11A3: DTC Description.

  • DTC P11A4: DTC Description.

  • DTC P11A6: DTC Description.

  • DTC P11A7: DTC Description.

  • DTC P11AB: DTC Description.

  • DTC P11AC: DTC Description.

  • DTC P11AD: DTC Description.

  • DTC P11AE: DTC Description.

  • DTC P11AF: DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

  1. Ignition switch OFF and wait at least 10 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 12 V or more with ignition switch ON.

YES>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and warm it up to the normal operating temperature.

  2. Keep the engine speed between 4,500 rpm for at least 12 seconds under no load.

  3. Check 1st trip DTC.

Is DTC P11A8 detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P11A8 is displayed with the following DTC, perform the confirmation procedure (trouble diagnosis) for the applicable DTC.

Is DTC P11A0, P11A1, P11A2, P11A3 P11A4, P11A6, P11A7, P11AB, P11AC, P11AD, P11AE or P11AF detected?

YES>>

Perform diagnosis of applicable.

  • DTC P11A0: DTC Description.

  • DTC P11A1: DTC Description.

  • DTC P11A2: DTC Description.

  • DTC P11A3: DTC Description.

  • DTC P11A4: DTC Description.

  • DTC P11A6: DTC Description.

  • DTC P11A7: DTC Description.

  • DTC P11AB: DTC Description.

  • DTC P11AC: DTC Description.

  • DTC P11AD: DTC Description.

  • DTC P11AE: DTC Description.

  • DTC P11AF: DTC Description.

NO>>

GO TO 2.

CHECK VCR MOTOR

Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace VCR actuator. Refer to Removal and Installation.

    P11a7 Vcr Stopper Position
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11A7 00 VCR stopper position (Variable compression ratio stoppe...
    P11a9 Vcr Target Angle
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11A9 00 VCR target angle (Variable compression ratio target ang...

    Other materials:

    2wd. Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting
    Noise, Vibration and Harshness (nvh) Troubleshooting NVH Troubleshooting Chart Use chart below to find the cause of the symptom. If necessary, repair or replace these parts. Possible cause and SUSPECTED PARTS Symptom Reference REAR AXLE Noise Shake Vibration Shimmy Judder Poor quality ...

    Diagnosis System (tcm)
    Diagnosis Description 1 Trip Detection Diagnosis and 2 Trip Detection Diagnosis NOTE: “Start the engine and turn OFF the ignition switch after warm-up.” This is defined as 1 trip. 1 TRIP DETECTION DIAGNOSISWhen initial malfunction is detected, TCM memorizes DTC. In these diagnoses, some ...

    Dtc/circuit Diagnosis. Power Supply and Ground Circuit
    Moonroof Motor Assembly Diagnosis Procedure CHECK FUSE Ignition switch OFF. Check that the following fuse is not blown (open): Fuse No. Capacity 31 15 A Is the fuse blown (open)? YES>> Repair the blown (open) fuse after repairing the affected circuit if a fuse ...