Nissan Rogue (T33) 2021-Present Service Manual: P11a7 Vcr Stopper Position

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P11a7 Vcr Stopper Position

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P11A7 00

VCR stopper position

(Variable compression ratio stopper position) 		Diagnosis condition Engine running at idle
Signal (terminal) —
Threshold Detect position gap between the stopper position (position at highest compression rate) and the learnt position.
Diagnosis delay time 40 seconds or more

POSSIBLE CAUSE

  • VCR actuator

  • Arm slip

  • Internal gear trouble of VCR actuator

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC P11A7 is displayed with the following DTC, perform the confirmation procedure (trouble diagnosis) for the applicable DTC.

Is DTC P11A0, P11A2, P11A3 P11A4, P11AC, P11AD, P11AE or P11AF detected?

YES>>

Perform diagnosis of applicable.

  • DTC P11A0: DTC Description.

  • DTC P11A2: DTC Description.

  • DTC P11A3: DTC Description.

  • DTC P11A4: DTC Description.

  • DTC P11AC: DTC Description.

  • DTC P11AD: DTC Description.

  • DTC P11AE: DTC Description.

  • DTC P11AF: DTC Description.

NO>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Warm up the engine to the normal operating temperature and keep the engine speed at idle for 1 minutes.

  2. Check 1st trip DTC.

Is DTC P11A7 detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK VCR ACTUATOR

Check VCR actuator visually.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK FUNCTION OF VCR SYSTEM

  1. Start engine and warm it up to the normal operating temperature.

  2. Stop the engine.

  3. Ignition switch ON.

  4. Select "VCR system" in "ACTIVE TEST" mode of "ENGINE" using CONSULT.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace VCR actuator.

PERFORM VCR BASE POSITION LEARNING

  1. Start engine.

  2. Perform VCR base position learning.

  3. Perform DTC confirmation procedure.

Is the DTC P11A7 displayed again?

YES>>

Replace VCR actuator. Refer to Removal and Installation.

NO>>

INSPECTION END

    P11a6 Vcr Rotation Angle Sensor A/b
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11A6 00 VCR rotation angle sensor mutual (Variable compression ...
    P11a8 Vcr Target Angle
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11A8 00 VCR target angle (Variable compression ratio target ang...

    Other materials:

    It Can Communication Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the diagnostic CAN communication circuit normal? YES>> GO TO 2. NO>> Check and repair diagnostic CAN commu ...

    Tcm
    Reference Value CONSULT DATA MONITOR STANDARD VALUE In CONSULT, electric shift timing or lock-up timing, i.e. operation timing of each solenoid valve, is displayed. Therefore, if there is an obvious difference between the shift timing estimated from a shift shock (or engine speed variation ...

    B2231-16 Battery Voltage
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detected condition B2231-16 Battery voltage (Battery voltage) Diagnosis condition When ignition switch is ON. Signal (terminal) Battery power supply Threshold 8 V or le ...