Nissan Rogue (T33) 2021-Present Service Manual: P1197 Out of Gas

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P1197 Out of Gas

DTC Description

This diagnosis result is detected when the fuel level of the fuel tank is extremely low and the engine does not run normally.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P1197 00

FUEL RUN OUT

(Out of gas) 		A Diagnosis condition —
Signal (terminal) Fuel rail pressure sensor signal
Threshold Fuel rail pressure remains at 1.1 MPa (11 bar, 11.2 kg/cm2, 159.5 psi) or less with the fuel level too low
Diagnosis delay time 5 seconds or more
B Diagnosis condition —
Signal (terminal) Fuel rail pressure sensor signal
Threshold Fuel rail pressure remains 2.7 MPa (27 bar, 27.5 kg/cm2, 392 psi) lower than a target fuel pressure with the fuel level too low
Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

  • Fuel cut

  • Harness or connectors (Fuel pump circuit is open or shorted.)

    • Fuel pump circuit is open or shorted.

    • High pressure fuel pump circuit is open or shorted.

    • High pressure fuel pump relay circuit

  • Fuel pump

  • Fuel pressure regulator

  • Fuel pump system

  • High pressure fuel pump

  • High pressure fuel pump system

  • High pressure fuel pump relay

  • Fuel rail pressure sensor

  • Hose disconnection

FAIL-SAFE

Fail safe mode Nissan Ariya Vehicle behavior
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE-1

Start the engine.

Does the engine start?

YES>>

GO TO 3.

NO>>

Proceed to DTC Diagnosis Procedure.

PERFORM DTC CONFIRMATION PROCEDURE-2

  1. Start the engine and warm it up to normal operating temperature.

    NOTE:

    For best results, warm up the engine until “COOLANT TEMP/S” on “DATA MONITOR” mode of “ENGINE” using CONSULT reaches at least 70°C (158°F).

  2. Keep the engine speed at 3,500 rpm for 5 seconds and let it idle at least 1 minute.

  3. Check 1st trip DTC.

    NOTE:

    If the fuel tank has sufficient fuel, this diagnosis result may not be detected.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

REFUEL THE VEHICLE

  1. Refuel 10 liter (8 Imp qt).

    CAUTION:

    Never refuel more than 10 liter.

  2. Start the engine and keep the engine speed at 3,000 rpm for 30 seconds.

    NOTE:

    For best results, warm up the engine until “COOLANT TEMP/S” on “DATA MONITOR” mode of “ENGINE” using CONSULT reaches at least 70°C (158°F).

  3. Turn ignition switch OFF and wait at least 10 seconds.

  4. Turn ignition switch ON.

  5. Turn ignition switch OFF and wait at least 10 seconds.

  6. Turn ignition switch ON.

  7. Erase DTC.

  8. Start engine and let it idle for at least 60 seconds.

  9. Perform DTC Confirmation Procedure, again. Refer to DTC Description.

Is 1st trip DTC detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK FUEL PUMP

Check fuel pump. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace malfunctioning part.

CHECK HIGH PRESSURE FUEL PUMP

Check high pressure fuel pump. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check fuel hose connection.

NO>>

Repair or replace malfunctioning part.

    P1148 Closed Loop Control
    DTC Description DTC DETECTION LOGICNOTE: DTC P1148 is displayed with DTC for A/F sensor 1. When the DTC is detected, perform the trouble diagnosis of DTC corresponding to A/F se...
    P119a Fuel Rail Pressure Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P119A 00 FUEL PRESSURE SENSOR (Fuel pressure sensor) Diagnosis c...

    Other materials:

    P0532 A/c Refrigerant Pressure Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0532 00 REFRIGERANT PRESS SENSOR A (A/C refrigerant pressure sensor A circuit low) Diagnosis condition — Signal (terminal) Refrigerant pressure sens ...

    P052a Intake Valve Timing Control
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P052A 00 CAMSHAFT POSITION TIMING B1 (Cold start “A” camshaft position timing over-advanced bank 1) Diagnosis condition Cold condition Signal (terminal) ...

    P26a3 Multi-Way Control Valve Motor
    DTC Description DTC DETECTION LOGICNOTE: If DTC P26A3 is displayed with DTC P26A5, P26A6, and/or P26A7 first perform the trouble diagnosis for DTC P26A5, P26A6, and/or P26A7. Refer to DTC Index. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P26A3 00 ...