Nissan Rogue (T33) 2021-Present Service Manual: P10ca Internal Control Module Fuel Injector

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P10ca Internal Control Module Fuel Injector

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P10CA 00

Cylinder3 injector A

(Cylinder3 injector A) 		Diagnosis condition —
Signal (terminal) —
Threshold

  • Injector driver unit is malfunctioning.

  • ECM detects No. 3 injector circuit is shorted.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    • Fuel injector circuit is open

  • Battery power supply

  • ECM (Direct injector driver unit)

  • Fuel injector

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

NOTE:

ECM does not control the accelerator pedal releasing speed.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited. When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

  • Before performing the following procedure, confirm that battery voltage is between 12 - 15 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for at least 20 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK FUEL INJECTOR

Check fuel injector. Refer to Component Function Check.

Is inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

  4. Check 1st trip DTC.

Is the DTC displayed again?

YES>>

Replace ECM. Refer to ECM : Removal & Installation.

NO>>

INSPECTION END

    P10c9 Internal Control Module Fuel Injector
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P10C9 00 Internal control module fuel injector (Internal control...
    P1148 Closed Loop Control
    DTC Description DTC DETECTION LOGICNOTE: DTC P1148 is displayed with DTC for A/F sensor 1. When the DTC is detected, perform the trouble diagnosis of DTC corresponding to A/F se...

    Other materials:

    B2720-05 Corner Sensor [rl]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2720-05 CORNER SENSOR [RL] (Corner sensor [rear left]) Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Configuration of so ...

    Dtc/circuit Diagnosis. B2416-15 Touch Sensor Circuit Rh Open
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2416-15 Touch sensor circuit RH open (Touch sensor circuit right hand open) Diagnosis condition All times Signal (terminal) Touch sensor RH signal Thr ...

    Cvt: Ge0f14a. Symptom Diagnosis
    Cvt Control System Symptom Table The diagnosis item number indicates the order of check. Start checking in the order from 1. Perform diagnoses of symptom table 1 before symptom table 2. Symptom Table 1 Diagnostic item Reference Symptom Shift Shock Slips/Will Not Engage Other ...