Nissan Rogue (T33) 2021-Present Service Manual: P10c8 Internal Control Module Fuel Injector

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P10c8 Internal Control Module Fuel Injector

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P10C8 00

Cylinder1 injector A

(Cylinder1 injector A) 		Diagnosis condition —
Signal (terminal) —
Threshold

  • Injector driver unit is malfunctioning.

  • ECM detects No. 1 injector circuit is shorted.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    • Fuel injector circuit is open

  • Battery power supply

  • ECM (Direct injector driver unit)

  • Fuel injector

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

NOTE:

ECM does not control the accelerator pedal releasing speed.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited. When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

  • Before performing the following procedure, confirm that battery voltage is between 12 - 15 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for at least 20 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK FUEL INJECTOR

Check fuel injector. Refer to Component Function Check.

Is inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

  4. Check 1st trip DTC.

Is the DTC displayed again?

YES>>

Replace ECM. Refer to ECM : Removal & Installation.

NO>>

INSPECTION END

    P1099 Humidity Temperature Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1099 00 Humidity temperature sensor (Humidity temperature senso...
    P10c9 Internal Control Module Fuel Injector
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P10C9 00 Internal control module fuel injector (Internal control...

    Other materials:

    System
    Can Communication System System Description SYSTEM DIAGRAM With type B meter With type A meter Without ProPILOT Assist 2.1 With type A meter With ProPILOT Assist 2.1 DESCRIPTION CAN (Controller Area Network) is a serial communication line for real time application. It ...

    System Description. Diagnosis System (hands Free Module)
    Diagnosis Description APPLICATION ITEMCONSULT performs the following functions via CAN communication with Intelligent Key unit: Diagnosis mode Function Self diagnosis result Display non-network DTC which Intelligent Key unit memorizes ECU identification The Intelligent Key unit part ...

    P2a01 Ho2s2
    DTC Description The heated oxygen sensor 2 has a much longer switching time between rich and lean than the air fuel ratio (A/F) sensor 1. The oxygen storage capacity of the three way catalyst (manifold) causes the longer switching time.MALFUNCTION ATo judge the malfunctions of heated oxygen ...