Nissan Rogue (T33) 2021-Present Service Manual: P062f Ecm

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P062f Ecm

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P062F 00

CONTROL MODULE

(Internal control module EEPROM error) 		Diagnosis condition Ignition switch ON
Signal (terminal) —
Threshold EEPROM (built-in microcomputer) system internal ECM does not function properly
Diagnosis delay time —

POSSIBLE CAUSE

ECM

FAIL-SAFE

Engine Control System

Not applicable

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited. When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is between 11 V  or more with ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 1 second.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Repeat step 1 and 2 for 10 times.

  4. Erase DTC.

  5. Turn ignition switch OFF and wait at least 10 seconds

  6. Turn ignition switch ON.

  7. Check the DTC.

Is the DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

INSPECTION START

  1. Turn ignition switch ON and wait at least 1 second.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Repeat step 1 and 2 for 10 times.

  4. Erase DTC.

  5. Turn ignition switch OFF and wait at least 10 seconds

  6. Turn ignition switch ON.

  7. Check the DTC.

Is DTC erased?

YES>>

INSPECTION END

NO>>

GO TO 2.

REPLACE ECM

  1. Replace ECM. Refer to ECM : Removal & Installation.

  2. Refer to Work Procedure.

>>

INSPECTION END

    P062d Fuel Injector Driver Bank 1
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P062D 00 Fuel injector driver bank 1 (Fuel Injector Driver Circu...
    P0641 Sensor Power Supply
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0641 00 Sensor reference voltage A (Sensor reference voltage ...

    Other materials:

    U2141 Can Comm Circuit
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U2141 57 CAN comm err (TCM) [CAN comm err (TCM)] Diagnosis condition Ignition switch ON Signal (terminal) CAN communication signal Threshold MA ...

    P2135 Tp Sensor
    DTC Description DTC DETECTION LOGICNOTE: If DTC P2135 is displayed with DTC P06B0, first perform the trouble diagnosis for DTC P06B0. Refer to DTC Description. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2135 00 TP SENSOR-B1 (Throttle/Pedal ...

    Component Parts
    Meter System Component Parts Location 2WD MODELS A. View with rear seat removed B. View with engine assembly removed     No. Component Function 1. Washer fluid level switch (if so equipped) Transmits the washer fluid level switch signal to the combination me ...