Nissan Rogue (T33) 2021-Present Service Manual: P044a Egr Volume Contro Valve Position Sensor

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P044a Egr Volume Contro Valve Position Sensor

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P044A 00

EGR SENSOR C

(EGR sensor C circuit low) 		Diagnosis condition Ignition switch ON
Signal (terminal) EGR volume control valve signal
Threshold ECM detects that a voltage signal from EGR volume control valve position sensor is less than 4.81 V for 5 consecutive seconds.
Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

  • Harness or connectors

    (EGR volume control valve position sensor circuit is open or shorted.)

  • EGR volume control valve

FAIL-SAFE

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

NOTE:

ECM does not control the accelerator pedal releasing speed.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P044A is displayed with DTC P06B0, first perform trouble diagnosis for DTC P06B0.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 5 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P044A is displayed with DTC P06B0, first perform trouble diagnosis for DTC P06B0.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

CHECK EGR VOLUME CONTROL VALVE POSITION SENSOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect EGR volume control valve harness connector.

  3. Turn ignition switch ON.

  4. Check voltage between EGR volume control valve harness connector and ground.

    + −

    Voltage

    (Approx.)
    EGR volume control valve
    Connector Terminal
    F81 3 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Perform the trouble diagnosis for power supply circuit.

CHECK EGR VOLUME CONTROL VALVE POSITION SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check harness continuity between EGR volume control valve harness connector and ECM harness connector.

    EGR volume control valve ECM Continuity
    Connector Terminal Connector Terminal
    F81 2 F71 107 Existed

  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK EGR VOLUME CONTROL VALVE POSITION SENSOR INPUT SIGNAL CIRCUIT

  1. Check harness continuity between EGR volume control valve harness connector and ECM harness connector.

    EGR volume control valve ECM Continuity
    Connector Terminal Connector Terminal
    F81 1 F71 116 Existed

  2. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK EGR VOLUME CONTROL VALVE

Check the EGR volume control valve. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace EGR volume control valve. Refer to Removal and Installation.

    P0446 Evap Canister Vent Control Valve
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0446 00 VENT CONTROL VALVE (EVAP System Vent Control Circuit) D...
    P044b Egr Volume Control Valve Position Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P044B 00 EGR SENSOR C (EGR Sensor "C" Circuit Range/Performance)...

    Other materials:

    Dtc/circuit Diagnosis. C1700-54 Control Unit
    DTC Description NOTE: The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information. Activate and display TPMS sensor IDs Display tire pressure reported by the TPMS sensor Read TPMS DTCs ...

    Removal/replacement of Rear Brake Pad or Rear Brake Caliper
    Description CAUTION: When performing the following operations, always use CONSULT, for performing “START BRAKE PAD REPLACEMENT”, “FINISH BRAKE PAD REPLACEMENT”, “INITIALIZATION POSITION ADJUSTMENT” of “Work support”. Refer to Work Procedure. ×: Required —: not required ...

    Basic Inspection. Diagnosis and Repair Work Flow
    Work Flow OVERALL SEQUENCE Reference 1··· Refer to CONSULT Function. Reference 2··· Refer to DTC Index. Reference 3··· Refer to Symptom Table. DETAILED FLOWINTERVIEW AND SYMPTOM CONFIRMATION Check the malfunction symptoms by performing the following items. Interview t ...