Nissan Rogue (T33) 2021-Present Service Manual: P0261 Fuel Injector (cylinder 1)

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P0261 Fuel Injector (cylinder 1)

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P0261 00

CYL1 INJECTOR

(Cylinder 1 Injector A Circuit Low) 		Diagnosis condition —
Signal (terminal) —
Threshold Direct injector driver unit is malfunctioning.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    • direct fuel injector circuit is shorted

  • Battery power supply

  • ECM (direct injector driver unit)

FAIL-SAFE

Engine Control System

Fail safe mode Nissan Ariya Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

NOTE:

ECM does not control the accelerator pedal releasing speed.
Device fix mode

  • This mode fixes the electric IVT control actuator and the EVT control solenoid valve in the reference position.

  • A control signals is not transmitted to the EGR volume control valve and the EGR volume control is deactivated.
Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

Stop/Start System

When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited.

When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

  • Before performing the following procedure, confirm that battery voltage is between 12 - 15 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for at least 20 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DIRECT FUEL INJECTOR

Check direct fuel injector. Refer to Component Inspection.

Is inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

  4. Check 1st trip DTC.

Is the DTC P0261 displayed again?

YES>>

Replace ECM. Refer to ECM : Removal & Installation.

NO>>

INSPECTION END

    P025c Fuel Pump Relay
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P025C 00 Fuel pump module A (Fuel Pump Module "A" Control Circui...
    P026b Injection Timing
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P026B 00 Injection timing Diagnosis condition — Signal — Thr...

    Other materials:

    P023a Charge Air Cooler Cooling Electric Water Pump
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P023A 00 Charged air cooler coolant pump (Charge Air Cooler Coolant Pump Control Circuit/Open) Diagnosis condition Engine running at idle Warm-up con ...

    Rear Door Alert
    The Rear Door Alert system helps remind the driver to check the rear seat(s) before leaving the Nissan Rogue. Under certain conditions, the system indicates that an object or passenger may still be in the rear seat. The Rear Door Alert system is initially disabled. The driver can enable the system ...

    Fuel Injector Offset Learning
    Description Fuel injector offset learning is an operation to allow ECM to learn fuel injector offset data. This operation must be performed after the following parts are replaced: Each time injector or ECM is replaced. (For details, refer to Work Procedure.) Work Procedure PRECONDITIONI ...