Nissan Rogue (T33) 2021-Present Service Manual: P025c Fuel Pump Relay

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P025c Fuel Pump Relay

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P025C 00

Fuel pump module A

(Fuel Pump Module "A" Control Circuit Low) 		Diagnosis condition Engine running
Signal (terminal) —
Threshold An excessively low voltage from the fuel pump and FPCM is sent to the ECM.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    (Fuel pump and FPCM circuit is open or shorted.)

  • Fuel pump and FPCM

  • ECM

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

  • Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.

  • Before performing the following procedure, check that the engine coolant temperature is −10°C (14°F) or more.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for at least 5 seconds.

    If engine does not start, crank engine for at least 5 seconds.

  2. Check DTC.

Is the DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK FPCM SIGNAL CIRCUIT-1

  1. Turn ignition switch OFF

  2. Disconnect FPCM harness connector and ECM connector.

  3. Check the continuity between FPCM harness connector and ECM harness connector.

    ECM Fuel level sensor unit and fuel pump Continuity
    Connector Terminal Connector Terminal
    E21 138 B97 5 Existed
    144 4

  4. Also check harness for short to ground.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

REPLACE FUEL LEVEL SENSOR UNIT AND FUEL PUMP

  1. Replace fuel level sensor unit and fuel pump. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure again. Refer to DTC Description.

  3. Check the DTC.

Is the DTC P025C displayed again?

YES>>

GO TO 3.

NO>>

INSPECTION END

REPLACE ECM

  1. Replace ECM. Refer to ECM : Removal & Installation.

  2. Perform DTC confirmation procedure again. Refer to DTC Description.

  3. Check the DTC.

Is the DTC P025C displayed again?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

INSPECTION END

    P025b Fuel Pump Module a
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P025B 00 FUEL PUMP MODULE A (Fuel Pump Module "A" Control Circui...
    P0261 Fuel Injector (cylinder 1)
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0261 00 CYL1 INJECTOR (Cylinder 1 Injector A Circuit Low) Diagn...

    Other materials:

    P1536 Ascd System
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1536 00 Cruise control (Cruise control) Diagnosis condition Ignition switch ON Signal CAN communication signal Threshold ECM cannot receive a ...

    Intelligent Key
    CONSULT Function (BCM - INTELLIGENT KEY) DATA MONITORNOTE: The following table includes information (items) inapplicable to this Nissan Ariya vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items. Monitor Item Condition Stop/start switch [On/Off] ...

    Removal and Installation. Steering Gear and Linkage
    Exploded View 1. Outer socket 2. Boot clamp (small diameter) 3. Boot 4. Boot clamp (large diameter) 5. Hole cover seal A. Outer socket lock nut. B. Inner socket lock nut. — — — — CAUTION: Never apply the grease to the surface be ...