Nissan Rogue (T33) 2021-Present Service Manual: P00c0 Turbocharger Bypass Control Valve

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P00c0 Turbocharger Bypass Control Valve

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P00C0 00

Turbocharger/Supercharger Bypass Valve B

(Turbocharger/Supercharger Bypass Valve B Control Circuit) 		Diagnosis condition —
Signal (terminal) —
Threshold An excessively low voltage from the turbocharger bypass control valve is sent to ECM.
Diagnosis delay time 5 consecutive seconds

POSSIBLE CAUSE

  • Harness or connectors

    (Turbocharger bypass control valve circuit is open.)

  • Turbocharger bypass control valve

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 5 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

TURBOCHARGER BYPASS CONTROL VALVE POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect turbocharger bypass control valve harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between turbocharger bypass control valve harness connector and ground.

    + − Voltage
    Turbocharger bypass control valve
    Connector Terminal
    F104 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Perform the trouble diagnosis for power supply circuit.

CHECK TURBOCHARGER BYPASS CONTROL VALVE INPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between turbocharger bypass control valve harness connector and ECM harness connector.

    Turbocharger bypass control valve ECM Continuity
    Connector Terminal Connector Terminal
    F104 2 F72 26 Existed

  4. Also check harness for short to power or short to ground.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK TURBOCHARGER BYPASS CONTROL VALVE

Check the turbocharger bypass control valve. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace turbocharger assembly (do not replace bypass control valve only). Refer to Exploded View.

    P00b3 Engine Coolant Temperature Sensor 2
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P00B3 00 RADIATOR COOLANT TEMP SEN (Radiator coolant temperature...
    P00d2 Ho2s2 Heater
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P00D2 00 Heated O2 sensor heater B1 sensor 2 (HO2S heater contro...

    Other materials:

    Symptom Diagnosis. Door Does Not Lock/unlock with Door Request Switch and Intelligent Key
    Description All doors do not lock/unlock using door request switch.SYMPTOM TABLE (BOTH INTELLIGENT KEYS HAVE THE SAME SYMPTOMS) Door lock operation (remote keyless entry) Door lock operation (request switch of front/rear/back door) or trunk/back door open operation (opener switch of trunk/back ...

    Rear Final Drive: R145. Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting
    Noise, Vibration and Harshness (nvh) Troubleshooting NVH Troubleshooting Chart Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts. Possible cause and SUSPECTED PARTS Symptom Reference Noise Vibration Gear tooth rough × – Inspectio ...

    Input Speed Sensor
    Exploded View 1. O-ring 2. Input speed sensor 3. Transaxle assembly : N·m (kg-m, in-lb) : Always replace after every disassembly. : Apply petroleum jelly. Removal and Installation REMOVAL Never Reuse These Parts Part Code For additional information: Seal-O-ring 31051 ...