Nissan Rogue (T33) 2021-Present Service Manual: P00b3 Engine Coolant Temperature Sensor 2

Nissan Rogue (T33) 2021-Present Service Manual / Engine :: Engine Control System / Kr15ddt :: Dtc/circuit Diagnosis / P00b3 Engine Coolant Temperature Sensor 2

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
P00B3 00

RADIATOR COOLANT TEMP SEN

(Radiator coolant temperature sensor circuit low) 		Diagnosis condition —
Signal (terminal) —
Threshold

ECM detects the following status continuously for 5 seconds or more:

A voltage signal transmitted from the engine coolant temperature sensor 2 is 0.04 V or less.
Diagnosis delay time 5 consecutive seconds

POSSIBLE CAUSE

  • Harness or connectors

    (Engine coolant temperature sensor 2 circuit is open or shorted.)

  • Engine coolant temperature sensor 2

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 5 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

DTC Diagnosis Procedure

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ENGINE COOLANT TEMPERATURE SENSOR 2 POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect engine coolant temperature (ECT) sensor 2 harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between ECT sensor 2 harness connector and ground.

    + −

    Voltage

    (Approx.)
    ECT sensor 2
    Connector Terminal
    F21 2 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 4.

CHECK ENGINE COOLANT TEMPERATURE SENSOR 2 GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between ECT sensor 2 harness connector and ECM harness connector.

    ECT sensor 2 ECM Continuity
    Connector Terminal Connector Terminal
    F21 1 F71 102 Existed

  4. Also check harness for short to ground to power.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK ENGINE COOLANT TEMPERATURE SENSOR 2

Check the engine coolant temperature sensor 2. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace engine coolant temperature sensor 2. Refer to Exploded View.

CHECK ENGINE COOLANT TEMPERATURE SENSOR 2 POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between ECT sensor 2 harness connector and ECM harness connector.

    ECT sensor 2 ECM Continuity
    Connector Terminal Connector Terminal
    F21 2 F71 87 Existed

  4. Also check harness for short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

    P0097 Iat Sensor 2
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0097 00 IAT SENSOR 2 B1 (Intake air temperature sensor 2 circui...
    P00c0 Turbocharger Bypass Control Valve
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P00C0 00 Turbocharger/Supercharger Bypass Valve B (Turbocharger/...

    Other materials:

    Precautions on seat belt usage
    When seat belts are worn correctly — with the occupant seated upright, positioned well back in the seat, and both feet on the floor — the risk of injury or fatality in an accident is significantly reduced. Proper seat belt use enhances the effectiveness of the Nissan Rogue safety systems, inclu ...

    P050a Cold Start Control
    DTC Description DESCRIPTIONECM controls ignition timing and engine idle speed when engine is started with pre-warming up condition.This control promotes the activation of three way catalyst by heating the catalyst and reduces emissions.DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diag ...

    P064a Fuel Pump Control Module
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P064A 00 Fuel pump control module A (Fuel Pump Control Module "A") Diagnosis condition Engine running Signal (terminal) — Threshold Voltage s ...