Nissan Rogue (T33) 2021-Present Service Manual: M&a Branch Line Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Electrical & Power Control :: Lan System / Can :: Dtc/circuit Diagnosis / M&a Branch Line Circuit

Diagnosis Procedure

CHECK CONNECTOR

  1. Turn the ignition switch OFF.

  2. Disconnect the battery cable from the negative terminal.

  3. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side).

    • Combination meter

    • BCM

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair the terminal and connector.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

  1. Disconnect the connector of BCM.

  2. Check the continuity between the BCM harness connector terminals.

  • With type B meter

    BCM harness connector Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    B26 87 E29 118 Existed
    86 117 Existed

  • With type A meter

    BCM harness connector Continuity
    Connector No. Terminal No. Connector No. Terminal No.
    B123 104 E60 106 Existed
    103 107 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Check the harness and repair the root cause (Nissan Ariya vehicle CAN communication 2 circuit side). Refer to Diagnosis Procedure.

CHECK HARNESS FOR OPEN CIRCUIT

  1. Connect the connector of BCM.

  2. Disconnect the connector of combination meter.

  3. Check the resistance between the combination meter harness connector terminals.

    • With type B meter

      Combination meter harness connector Resistance (Ω)
      Connector No. Terminal No.
      M76 18 19 Approx. 54 – 66

    • USA production type A meter

      Combination meter harness connector Resistance (Ω)
      Connector No. Terminal No.
      M73 18 19 Approx. 54 – 66

    • JAPAN production type A meter

      Combination meter harness connector Resistance (Ω)
      Connector No. Terminal No.
      M77 18 19 Approx. 54 – 66

Is the measurement value within the specification?

YES>>

GO TO 4.

NO>>

Repair the combination meter branch line.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the combination meter. Refer to the following.

  • Full TFT meter: Diagnosis Procedure

  • 7 inch information display: Diagnosis Procedure

Is the inspection result normal?

YES (Present error)>>

Replace the combination meter. Refer to the following.

  • Full TFT meter: Removal and Installation

  • 7 inch information display: Removal and Installation

YES (Past error)>>

Error was detected in the combination meter branch line.

NO>>

Repair the power supply and the ground circuit.

    Lib 12v Branch Line Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damag...
    Laser Branch Line Circuit
    Diagnosis Procedure CHECK CONNECTOR Turn the ignition switch OFF. Disconnect the battery cable from the negative terminal. Check the following terminals and connectors for damag...

    Other materials:

    P1226 Tp Sensor
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1226 00 CTP LEARNING-B1 (CTP LEARNING-B1) Diagnosis condition Ignition switch ON Signal (terminal) Electric throttle control actuator signal Thre ...

    P0385 Ckp Sensor 2
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0385 00 CKP SENSOR B (Crankshaft Position Sensor "B" Circuit) Diagnosis condition Engine running Signal (terminal) Crankshaft position sensor 2 signal ...

    Removal and Installation. Center Console Assembly
    Exploded View 1. Console finisher tray mat (if equipped) 2. Console finisher assembly 3. Instrument side panel LH 4. Panel console LH 5. Center console assembly 6. Console rear finisher 7. Console upper finisher 8. Console lid assembly 9. Pane ...