Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Power Supply and Ground Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Roof / Dtc/circuit Diagnosis :: Power Supply and Ground Circuit

Moonroof Motor Assembly

Diagnosis Procedure

CHECK FUSE

  1. Ignition switch OFF.

  2. Check that the following fuse is not blown (open):

    Fuse No. Capacity
    31 15 A

Is the fuse blown (open)?

YES>>

Repair the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK MOONROOF MOTOR ASSEMBLY POWER SUPPLY

  1. Disconnect moonroof motor assembly connector.

  2. Ignition switch ON.

  3. Check voltage between moonroof motor assembly harness connector and ground.

    (+) (—)

    Voltage

    (Approx.)
    Moonroof motor assembly
    Connector Terminal
    R4 6 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness.

CHECK MOONROOF MOTOR ASSEMBLY GROUND CIRCUIT

Check continuity between moonroof motor assembly harness connector and ground.

Moonroof motor assembly (—) Continuity
Connector Terminal
R4 1 Ground Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Repair or replace harness.

Sunshade Motor Assembly

Diagnosis Procedure

CHECK FUSE

  1. Ignition switch OFF.

  2. Check that the following fuse is not blown (open):

    Fuse No. Capacity
    31 15 A

Is the fuse blown (open)?

YES>>

Repair the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK SUNSHADE MOTOR ASSEMBLY POWER SUPPLY

  1. Disconnect sunshade motor assembly connector.

  2. Ignition switch ON.

  3. Check voltage between sunshade motor assembly harness connector and ground.

    (+) (—)

    Voltage

    (Approx.)
    Sunshade motor assembly
    Connector Terminal
    R5 6 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness.

CHECK SUNSHADE MOTOR ASSEMBLY GROUND CIRCUIT

Check continuity between sunshade motor assembly harness connector and ground.

Sunshade motor assembly (—) Continuity
Connector Terminal
R5 1 Ground Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis. B2f98-04 Sunshade Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition B2F98-04 Sunshade motor (Sunshade motor) Diagnosis condition...
    Dtc/circuit Diagnosis. Moonroof Switch Assembly
    Moonroof Switch Assembly (moonroof Switch) Component Function Check CHECK MOONROOF FUNCTION Check moonroof tilt up/down, open/close operations with moonroof switch. Is the inspe...

    Other materials:

    Automatic Brake Hold. Removal and Installation
    Chassis Control Module Removal and Installation Removal and installation procedure of chassis control module. Refer to Removal and Installation. Automatic Brake Hold Switch Removal and Installation Removal and installation procedure of parking brake switch. Refer to Removal and Installation.NOTE: ...

    U2a8c-88 Ethernet Circuit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detected condition U2A8C-88 Ethernet circuit Diagnosis condition When ignition switch is ON. Signal (terminal) — Threshold Lost ethernet communication with AV control unit Diagnosis delay time ...

    P11b0 Vcr Target Angle (cold Start)
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11B0 00 VCR target angle (cold start) [Variable compression ratio target angle (cold start)] Diagnosis condition Engine cold start Signal (terminal) ...