Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Moonroof Switch Assembly

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Roof / Dtc/circuit Diagnosis :: Moonroof Switch Assembly

Moonroof Switch Assembly (moonroof Switch)

Component Function Check

CHECK MOONROOF FUNCTION

Check moonroof tilt up/down, open/close operations with moonroof switch.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK MOONROOF SWITCH INPUT SIGNAL

  1. Ignition switch OFF.

  2. Disconnect moonroof switch assembly connector.

  3. Ignition switch ON.

  4. Check voltage between moonroof switch assembly harness connector and ground.

    (+) (—)

    Voltage

    (Approx.)
    Moonroof switch assembly
    Connector Terminal
    R21 2 Ground Battery voltage
    8
    9

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK MOONROOF SWITCH CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect moonroof motor assembly connector.

  3. Check continuity between moonroof motor assembly harness connector and moonroof switch assembly harness connector.

    Moonroof motor assembly Moonroof switch assembly Continuity
    Connector Terminal Connector Terminal
    R4 4 R21 2 Yes
    5 9
    10 8

  4. Check continuity between moonroof switch assembly harness connector and ground.

    Moonroof switch assembly (—) Continuity
    Connector Terminal
    R21 2 Ground No
    8
    9

Is the inspection result normal?

YES>>

Replace moonroof motor assembly. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK MOONROOF SWITCH GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Check continuity between moonroof switch assembly harness connector and ground.

    Moonroof switch assembly (—) Continuity
    Connector Terminal
    R21 10 Ground Yes

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace the harness.

CHECK MOONROOF SWITCH

Check moonroof switch.

Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace moonroof switch assembly. Refer to Removal and Installation.

Component Inspection

CHECK MOONROOF SWITCH

  1. Ignition switch OFF.

  2. Disconnect moonroof switch assembly connector.

  3. Check continuity moonroof switch assembly terminals under the following conditions:

    Moonroof switch assembly Condition Continuity
    Terminals
    9 10 Moonroof switch OPEN Yes
    Other than above No
    8 Moonroof switch CLOSE Yes
    Other than above No
    2 Moonroof switch PUSH Yes
    Other than above No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace moonroof switch assembly. Refer to Removal and Installation.

Sunshade Switch

Component Function Check

CHECK SUNSHADE FUNCTION

Check sunshade open/close operations with sunshade switch.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK SUNSHADE SWITCH INPUT SIGNAL

  1. Ignition switch OFF.

  2. Disconnect moonroof switch assembly connector.

  3. Ignition switch ON.

  4. Check voltage between moonroof switch assembly harness connector and ground.

    (+) (—)

    Voltage

    (Approx.)
    Moonroof switch assembly
    Connector Terminal
    R21 7 Ground Battery voltage
    12

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK SUNSHADE SWITCH CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect sunshade motor assembly connector.

  3. Check continuity between sunshade motor assembly harness connector and moonroof switch assembly harness connector.

    Sunshade motor assembly Moonroof switch assembly Continuity
    Connector Terminal Connector Terminal
    R5 5 R21 7 Yes
    10 12

  4. Check continuity between moonroof switch assembly harness connector and ground.

    Moonroof switch assembly (—) Continuity
    Connector Terminal
    R21 7 Ground No
    12

Is the inspection result normal?

YES>>

Replace sunshade motor assembly. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK SUNSHADE SWITCH GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Check continuity between moonroof switch assembly harness connector and ground.

    Moonroof switch assembly (—) Continuity
    Connector Terminal
    R21 10 Ground Yes

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace the harness.

CHECK SUNSHADE SWITCH

Check sunshade switch.

Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace moonroof switch assembly. Refer to Removal and Installation.

Component Inspection

CHECK SUNSHADE SWITCH

  1. Ignition switch OFF.

  2. Disconnect moonroof switch assembly connector.

  3. Check continuity moonroof switch assembly terminals under the following conditions:

    Moonroof switch assembly Condition Continuity
    Terminals
    7 10 Sunshade switch OPEN Yes
    Other than above No
    12 Sunshade switch CLOSE Yes
    Other than above No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace Moonroof switch assembly. Refer to Removal and Installation.

    Dtc/circuit Diagnosis. Power Supply and Ground Circuit
    Moonroof Motor Assembly Diagnosis Procedure CHECK FUSE Ignition switch OFF. Check that the following fuse is not blown (open): Fuse No. Capacity 31 15 A Is the fuse blown (open)...
    Dtc/circuit Diagnosis. Communication Signal Circuit
    Component Function Check CHECK SUNSHADE FUNTION Check sunshade open/close operations with sunshade switch. Is the inspection result normal? YES>> Inspection End. NO>>...

    Other materials:

    System Description. System
    Lithium Ion Battery 12v System Description SYSTEM DIAGRAM Component Function 12V sub battery (lithium ion battery) Refer to 12V Sub Battery (Lithium Ion Battery). Combination Meter Receives li-ion battery error signal from 12V sub battery (lithium ion battery) through IPDM E/R via ...

    Back-Up Lamp Circuit
    Component Function Check CHECK BACK-UP LAMP OPERATION Start the engine. With operating the shift selector, check that the back-up lamp is turned ON. Shift selector position: R range : Back-up lamp ON Shift selector position: Other than above : Back-up lamp OFF Is th ...

    P1564 Ascd Steering Switch
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1564 00 ASCD SW (ASCD SW) Diagnosis condition — Signal (terminal) ASCD steering switch signal Threshold ECM detects that input signal from t ...