Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Power Supply and Ground Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Power Window Control System / Dtc/circuit Diagnosis :: Power Supply and Ground Circuit

Power Window Main Switch

Diagnosis Procedure

CHECK FUSE

  1. Ignition switch OFF, and then wait for 3 minutes with driver door open.

    NOTE:

    • Even after ignition switch is OFF, power is supplied to accessories for a certain amount of timer by the AUTO ACC function.

    • When Nissan Ariya vehicle is operate while on standby, power may be supplied to accessories.

  2. Check that the following fuse is not blown (open):

    Fuse No. Capacity
    45 5 A

Is the fuse blown (open)?

YES>>

Repair the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY

  1. Disconnect power window main switch connector.

  2. Ignition switch ON.

  3. Check voltage between power window main switch harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Power window main switch
    Connector Terminal

    D6*1

    D27*2    		 3 Ground Battery voltage

    *1: With automatic drive positioner

    *2: Without automatic drive positioner

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness.

CHECK POWER WINDOW MAIN SWITCH GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Check continuity between power window main switch harness connector and ground.

    Power window main switch (–) Continuity
    Connector Terminal

    D6*1

    D27*2    		 22 Ground Yes

    *1: With automatic drive positioner

    *2: Without automatic drive positioner

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Repair or replace harness.

Front Power Window Switch Lh

Diagnosis Procedure

CHECK FUSE

  1. Ignition switch OFF.

  2. Check that the following fuse is not blown (open):

    Fuse No. Capacity
    59 20 A

Is the fuse blown (open)?

YES>>

Repair the blown (open) fuse repairing the affected circuit if a fuse blown (open).

NO>>

GO TO 2.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) POWER SUPPLY

  1. Disconnect front power window switch (passenger side) connector.

  2. Ignition switch ON.

  3. Check voltage between front power window switch (passenger side) harness connector and ground.

    (+) (−)

    Voltage

    (Approx.)
    Front power window switch (passenger side)
    Connector Terminal
    D112 6 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 3.

CHECK POWER WINDOW RELAY POWER SUPPLY

  1. Ignition switch OFF.

  2. Remove power window relay.

  3. Check voltage between fuse block (J/B) and ground.

    (+) (–)

    Voltage

    (Approx.)
    Fuse block (J/B)
    Terminal
    Power window relay 3 Ground Battery voltage
    2

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) POWER SUPPLY CIRCUIT

Check continuity between fuse block (J/B) and front power window switch (passenger side) harness connector.

Fuse block (J/B) Front power window switch (passenger side) Continuity
Terminal Connector Terminal
Power window relay 5 D112 6 Yes

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness.

CHECK POWER WINDOW RELAY CONTROL CIRCUIT

  1. Disconnect BCM connector.

  2. Check continuity between BCM harness connector and fuse block (J/B).

    BCM Fuse block (J/B) Continuity
    Connector Terminal Terminal
    With type A meter: M51 34 Power window relay 1 Yes
    With type B meter: M18 32

  3. Check continuity between BCM harness connector and ground.

    BCM — Continuity
    Connector Terminal
    With type A meter: M51 34 Ground No
    With type B meter: M18 32

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness.

CHECK POWER WINDOW RELAY

Check power window relay.

Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Replace power window relay.

CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Check continuity between front power window switch (passenger side) harness connector and ground.

    Front power window switch (passenger side) (–) Continuity
    Connector Terminal
    D112 3 Ground Yes
    7

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Repair or replace harness.

Rear Power Window Switch

Diagnosis Procedure

CHECK FUSIBLE LINK

  1. Ignition switch OFF.

  2. Check that the following fusible link is not blown (open):

    Fusible link No. Capacity
    KK 30 A

Is the fusible link blown (open)?

YES>>

Repair the blown (open) fusible link after repairing the affected circuit if a fusible link blown (open).

NO>>

GO TO 2.

CHECK REAR POWER WINDOW SWITCH POWER SUPPLY

  1. Disconnect rear power window switch connector.

  2. Ignition switch ON.

  3. Check voltage between rear power window switch harness connector and ground.

    (+) (−)

    Voltage

    (Approx.)
    Rear power window switch
    Connector Terminal
    LH D204 6 Ground Battery voltage
    RH D304

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 3.

CHECK POWER WINDOW RELAY POWER SUPPLY

  1. Ignition switch OFF.

  2. Remove power window relay.

  3. Check voltage between fuse block (J/B) and ground.

    (+) (–)

    Voltage

    (Approx.)
    Fuse block (J/B)
    Terminal
    Power window relay 3 Ground Battery voltage
    2

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK REAR POWER WINDOW SWITCH POWER SUPPLY CIRCUIT

Check continuity between fuse block (J/B) and rear power window switch harness connector.

Fuse block (J/B) Rear power window switch Continuity
Terminal Connector Terminal
Power window relay 5 LH D204 6 Yes
RH D304

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness.

CHECK POWER WINDOW RELAY CONTROL CIRCUIT

  1. Disconnect BCM connector.

  2. Check continuity between BCM harness connector and fuse block (J/B).

    BCM Fuse block (J/B) Continuity
    Connector Terminal Terminal
    With type A meter: M51 34 Power window relay 1 Yes
    With type B meter: M18 32

  3. Check continuity between BCM harness connector and ground.

    BCM (–) Continuity
    Connector Terminal
    With type A meter: M51 34 Ground No
    With type B meter: M18 32

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness.

CHECK POWER WINDOW RELAY

Check power window relay.

Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Replace power window relay.

CHECK REAR POWER WINDOW SWITCH GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Check continuity between rear power window switch harness connector and ground.

    Rear power window switch (–) Continuity
    Connector Terminal
    LH D204 7 Ground Yes
    RH D304

Repair or replace harness.

YES>>

Inspection End.

NO>>

Repair or replace harness.

Front Power Window Motor (driver Side)

Diagnosis Procedure

CHECK FUSE

  1. Ignition switch OFF, and then wait for 3 minutes with driver door open.

    NOTE:

    • Even after ignition switch is OFF, power is supplied to accessories for a certain amount of timer by the AUTO ACC function.

    • When Nissan Ariya vehicle is operate while on standby, power may be supplied to accessories.

  2. Check that the following fuse is not blown (open):

    Fuse No. Capacity
    52 20 A

Is the fuse blown (open)?

YES>>

Repair the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) POWER SUPPLY

  1. Disconnect front power window motor (driver side) connector.

  2. Ignition switch ON.

  3. Check voltage between front power window motor (driver side) harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Front power window motor (driver side)
    Connector Terminal
    D10 4 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness.

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Check continuity between front power window motor (driver side) harness connector and ground.

    Front power window motor (driver side) (–) Continuity
    Connector Terminal
    D10 3 Ground Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis. B2c41-04 Power Window Motor Fl
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition B2C41-04 Power window motor FL [Front power window motor (dr...
    Dtc/circuit Diagnosis. Power Window Main Switch
    Component Function Check CHECK POWER WINDOW MAIN SWITCH FUNCTION Check front power window motor (driver side) operation using power window main switch. Is the inspection result ...

    Other materials:

    Basic Inspection. Additional Service When Replacing Ecm
    Description Performing the following procedure can automatically activate recommunication of ECM and Intelligent Key unit, but only when the ECM is replaced with a new one*. For details, refer to Work Procedure.*: New one means a virgin ECM that has never been energized on-board.(In this step, ...

    P1c90-49 Sub Starter & Generator
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition P1C90-49 Sub starter & generator (Sub starter & generator) Diagnosis condition Engine running at idle Signal (terminal) - Threshold Sub starte ...

    Removal and Installation. Moonroof Switch Assembly
    Removal and Installation REMOVALRemove map lamp finisher. Removal and Installation Disengage moonroof switch assembly fixing pawls using a remover tool, and then remove moonroof switch assembly from map lamp finisher . : Pawl INSTALLATIONInstall in the reverse order of removal. ...