Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Front Wiper Motor Hi Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Driver Controls :: Wiper & Washer / Dtc/circuit Diagnosis :: Front Wiper Motor Hi Circuit

Component Function Check

CHECK FRONT WIPER INITIAL LO OPERATION

CONSULT

  1. Select “Front wiper” in “Active test” mode of “BCM [WIPER]”.

  2. Check the "Low" front wiper motor operation in the "Active test".

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Refer to Diagnosis Procedure.

CHECK FRONT WIPER HI OPERATION

CONSULT

  1. Move the front wiper switch between OFF and HI position.

  2. Check front wiper motor operation.

    Hi : Front wiper (HI) operation
    Off : Stop the front wiper

Is the inspection result normal?

YES>>

Front wiper motor HI circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK FRONT WIPER MOTOR (HI) OUTPUT VOLTAGE

  1. Ignition switch OFF.

  2. Disconnect front wiper motor connector.

  3. Ignition switch ON.

  4. Turn front wiper switch to HIGH.

  5. Check voltage between front wiper motor harness connector and ground.

    (+) (−) Condition

    Voltage

    (Approx.)
    Front wiper motor
    Connector Terminal
    E20 5 Ground Front wiper switch High

    Battery voltage

    (10 seconds*)

*: According to front wiper protection function, IPDM E/R supplies voltage for 10 seconds (battery voltage) and then stops for 20 seconds (no voltage). This operation occurs repeatedly.

Is the inspection result normal?

YES>>

GO TO 3

NO>>

GO TO 2.

CHECK FRONT WIPER MOTOR (HI) CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector.

  3. Check continuity between IPDM E/R harness connector and front wiper motor harness connector.

    IPDM E/R Front wiper motor Continuity
    Connector Terminal Connector Terminal
    E121 45 E20 5 Yes

  4. Check continuity between IPDM E/R harness connector and ground.

    IPDM E/R (—) Continuity
    Connector Terminal
    E121 45 Ground No

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK FRONT WIPER MOTOR GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect front wiper motor connector.

  3. Check continuity between front wiper motor harness connector and ground.

    Front wiper motor (—) Continuity
    Connector Terminal
    E20 2 Ground Yes

Is the inspection result normal?

YES>>

Replace front wiper motor. Refer to Removal and Installation.

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis. Front Wiper Motor Lo Circuit
    Component Function Check CHECK FRONT WIPER LO OPERATION CONSULT Select “Front wiper” in “Active test” mode of “BCM [WIPER]”. With operating the test item, check fron...
    Dtc/circuit Diagnosis. Front Wiper Auto Stop Signal Circuit
    Component Function Check CHECK FRONT WIPER STOP POSITION SIGNAL CONSULT Select “FR WIPER STOP POSITION” in “Data monitor” mode of “IPDM E/R”. Operate the front wiper...

    Other materials:

    Dtc/circuit Diagnosis. B1029-09 Front Seat Belt Pre-Tensioner Lh
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B1029-09 Front seat belt pre-tensioner LH (Front seat belt pre-tensioner left hand) Diagnosis condition When ignition switch is ON. Signal (terminal) Front ...

    I-BSI driving situations
    Basic information Indicator on Indicator off Indicator flashing Illustration 1 — Approaching from behind Another vehicle approaching from behind Illustration 1: When another vehicle enters the monitored area from the rear in an adjacent lane, the side indicator light on the Nissan Rogue i ...

    Mac Key Writing
    Description When replacing around view monitor control unit, it is necessary to write MAC key to around view monitor control unit. Write MAC key to around view monitor control unit according to "MAC Key writing" procedure of "CONSULT Operation Manual". Refer to Work Procedure.CAUTION: During ...