Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Drive Mode Select Switch Circuit

Nissan Rogue (T33) 2021-Present Service Manual / Cruise Control & Driver Assistance :: Drive Mode System / Dtc/circuit Diagnosis :: Drive Mode Select Switch Circuit

Diagnosis Procedure

CHECK DRIVE MODE SELECT SWITCH SIGNAL CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect drive mode select switch harness connector and BCM harness connector.

  3. Check the continuity between drive mode select switch harness connector and BCM harness connector.

    2WD models with type B meter
    Drive mode select switch BCM Continuity
    Connector Terminal Connector Terminal
    M187 2 M19 80 Yes
    6 57
    2WD models with type A meter
    Drive mode select switch BCM Continuity
    Connector Terminal Connector Terminal
    M187 2 M18 1 Yes
    6 M62 169
    AWD models with type B meter
    Drive mode select switch BCM Continuity
    Connector Terminal Connector Terminal

    M186 (without hill descent control)

    M181 (with hill descent control)     		3 M18 25 Yes
    AWD models with type A meter
    Drive mode select switch BCM Continuity
    Connector Terminal Connector Terminal

    M186 (without hill descent control)

    M181 (with hill descent control)     		3 M62 166 Yes

  4. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair / replace harness or connector.

CHECK DRIVE MODE SELECT SWITCH GROUND CIRCUIT

Check the continuity between drive mode select switch harness connector and ground.

2WD models
Drive mode select switch – Continuity
Connector Terminal
M187 1 Ground Yes
AWD models
Drive mode select switch – Continuity
Connector Terminal

M186 (without hill descent control)

M181 (with hill descent control) 		4 Ground Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness or connector.

CHECK DRIVE MODE SELECT SWITCH

Check drive mode select switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace drive mode select switch. Refer to Removal and Installation.

Component Inspection

2WD models

CHECK DRIVE MODE SELECT SWITCH

  1. Ignition switch OFF.

  2. Disconnect drive mode select switch harness connector.

  3. Check the continuity between drive mode select switch terminals as follows.

    Drive mode select switch Condition Continuity
    Terminals
    1 2 Switch to down-position. Existed
    Other than the above. Not existed
    6 Switch to up-position. Existed
    Other than the above. Not existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace drive mode select switch. Refer to Removal and Installation.

AWD models

CHECK DRIVE MODE SELECT SWITCH

  1. Ignition switch OFF and wait at least 10 seconds.

  2. Ignition switch ON.

  3. Check the indicator of AUTO on drive mode select switch indicator.

  4. Check the illuminated position changes according to the operation when switching the drive mode select switch.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace drive mode select switch. Refer to Removal and Installation.

    Basic Inspection. Diagnosis and Repair Work Flow
    Work Flow OVERALL SEQUENCEDETAILED FLOWGET INFORMATION FOR SYMPTOM Get the detailed information about symptom from customer. Check the drive mode indicator on the meter appeared...
    Removal and Installation. Drive Mode Switch
    Exploded View 2WD MODELS Console finisher Drive mode select switch Parking brake switch AWD MODELS Console finisher Drive mode select switch     Removal and Installati...

    Other materials:

    U0074-00 Av Communication
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition U0074-00 Control module comm Bus B Off (Control module communication bus B off) Diagnosis condition When ignition switch is ON Signal (terminal) AV communic ...

    Dtc/circuit Diagnosis. B1040-22 Vehicle Speed
    DTC Description DTC DETECTION LOGICNOTE: This DTC may be detected when drive the Nissan Ariya vehicle at vehicle speed of 186 MPH (300 km/h) or more. DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B1040-22 Nissan Ariya Vehicle speed (Vehicle speed) ...

    Intelligent Key
    CONSULT Function (BCM - INTELLIGENT KEY) DATA MONITORNOTE: The following table includes information (items) inapplicable to this Nissan Ariya vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items. Monitor Item Condition Stop/start switch [On/Off] ...