Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: Door Switch

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: Door Switch

Component Function Check

CHECK FUNCTION

CONSULT

  1. Select “Door switch driver”, “Door switch assist”, “Door switch rear left” and “Door switch rear right” in “Data monitor” mode of "BCM [DOOR LOCK]".

  2. Check that the function operates normally according to the following conditions:

Monitor item Condition Status
Door switch driver Front door LH Open On
Closed Off
Door switch assist Front door RH Open On
Closed Off
Door switch rear left Rear door LH Open On
Closed Off
Door switch rear right Rear door RH Open On
Closed Off

Is the inspection result normal?

YES>>

Door switch is OK.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK DOOR SWITCH INPUT SIGNAL

  1. Ignition switch OFF.

  2. Disconnect malfunctioning door lock assembly connector.

  3. Check voltage between malfunctioning door lock assembly harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Door lock assembly
    Connector Terminal
    Front LH D23 5 Ground Battery voltage
    Front RH D113 8
    Rear LH D206 5
    Rear RH D306 8

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK DOOR SWITCH CIRCUIT

  1. Disconnect BCM connector.

  2. Check continuity between door lock assembly harness connector and BCM harness connector.

    With Type B Meter
    Door lock assembly BCM Continuity
    Connector Terminal Connector Terminal
    Front LH D23 5 B26 81 Yes
    Front RH D113 8 93
    Rear LH D206 5 94
    Rear RH D306 8 95
    With Type A Meter
    Door lock assembly BCM Continuity
    Connector Terminal Connector Terminal
    Front LH D23 5 B123 97 Yes
    Front RH D113 8 98
    Rear LH D206 5 99
    Rear RH D306 8 100

  3. Check continuity between door lock assembly harness connector and ground.

    Door lock assembly — Continuity
    Connector Terminal
    Front LH D23 5 Ground No
    Front RH D113 8
    Rear LH D206 5
    Rear RH D306 8

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK DOOR SWITCH GROUND CIRCUIT

Check continuity between door lock assembly harness connector and ground.

Door lock assembly — Continuity
Connector Terminal
Front LH D23 6 Ground Yes
Front RH D113 7
Rear LH D206 6
Rear RH D306 7

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK DOOR SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace malfunctioning door lock assembly. Refer to Removal and Installation (front door) or Removal and Installation (rear door).

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

Inspection End.

Component Inspection

CHECK DOOR SWITCH

  1. Ignition switch OFF.

  2. Disconnect malfunctioning door lock assembly connector.

  3. Check continuity between door lock assembly terminals.

    Door lock assembly Condition Continuity
    Terminal
    Front LH 5 6 Door Closed No
    Opened Yes
    Front RH 7 8 Closed No
    Opened Yes
    Rear LH 5 6 Closed No
    Opened Yes
    Rear RH 7 8 Closed No
    Opened Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace malfunctioning door lock assembly. Refer to Removal and Installation (front door) or Removal and Installation (rear door).

    Dtc/circuit Diagnosis. Door Request Switch
    Component Inspection CHECK DOOR REQUEST SWITCH Ignition switch OFF. Disconnect malfunctioning door request switch connector. Check continuity between malfunctioning door request...
    Dtc/circuit Diagnosis. Hazard Function
    Component Function Check CHECK FUNCTION CONSULT Select “Flasher” in “Active test” mode of "BCM". Touch “LH” or “RH” to check that it works normally. Is the inspe...

    Other materials:

    P2135 Tp Sensor
    DTC Description DTC DETECTION LOGICNOTE: If DTC P2135 is displayed with DTC P06B0, first perform the trouble diagnosis for DTC P06B0. Refer to DTC Description. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2135 00 TP SENSOR-B1 (Throttle/Pedal ...

    Front and rear sonar system
    Basic information The sonar system uses sensors in the front and rear bumpers to warn the driver of nearby obstacles by emitting audible tones. When active, the sonar view appears automatically in the vehicle information display. WARNING The sonar system is a convenience feature and not a re ...

    B2fac-14 Accessory Relay
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition B2FAC-14 Accessory relay (Accessory relay) Diagnosis condition When ignition switch is OFF (not auto ACC status) Signal (terminal) Accessory relay control s ...