Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: C1741-21 Tire Pressure Sensor No Data Fl

Nissan Rogue (T33) 2021-Present Service Manual / Suspension :: Road Wheels & Tires / Dtc/circuit Diagnosis :: C1741-21 Tire Pressure Sensor No Data Fl

DTC Description

NOTE:

The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.

  • Activate and display TPMS sensor IDs

  • Display tire pressure reported by the TPMS sensor

  • Read TPMS DTCs

  • Register TPMS sensor IDs

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1741-21

Tire pressure sensor no data FL

(Tire pressure sensor no data front left) 		Diagnosis condition Drive at a speed of 25 MPH (40 km/h) or more reaches 10 minutes in total.
Signal (terminal) Tire pressure sensor signal.
Threshold Tire pressure data signal from the front left tire pressure sensor cannot be detected.
Diagnosis delay time 10 minutes or more.

POSSIBLE CAUSE

  • Driving in area with radio interference

  • Front left tire pressure sensor ID registration incomplete

  • Front left tire pressure sensor

  • Harness or connectors

  • BCM

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

TIRE PRESSURE SENSOR ID REGISTRATION

CONSULT

Perform tire pressure sensor ID registration. Refer to Description.

Can the tire pressure sensor ID registration be completed?

>>

GO TO 2.

PERFORM DTC CONFIRMATION

CONSULT

  1. Drive the Nissan Ariya vehicle at 25 MPH (40 km/h) or more until reaching 10 minutes in total.

    NOTE:

    Avoid driving in areas with radio interference.

  2. Stop the Nissan Ariya vehicle.

  3. Perform “Self diagnosis result” mode of “BCM”.

Is DTC “C1741-21” detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

NOTE:

The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.

  • Activate and display TPMS sensor IDs

  • Display tire pressure reported by the TPMS sensor

  • Read TPMS DTCs

  • Register TPMS sensor IDs

CHECK TIRE PRESSURE SIGNAL

CONSULT

  1. Select "Air pressure-front left" in "Data monitor" mode of "BCM [AIR PRESSURE MONITOR]".

  2. Check that the front left tire pressures match the standard value. Refer to Reference Value.

    NOTE:

    BCM holds last tire pressure values during 17 minutes after ignition switch is placed OFF.

Are all tire pressures displayed 0 kPa (psi)?

YES>>

GO TO 2.

NO>>

GO TO 3.

CHECK BCM POWER SUPPLY CIRCUIT

Check BCM power supply circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness or connectors.

TIRE PRESSURE SENSOR ID REGISTRATION

Perform tire pressure sensor ID registration. Refer to Description .

Can the tire pressure sensor ID registration be completed?

YES>>

GO TO 4.

NO>>

Replace applicable front left tire pressure sensor. Refer to Removal & Installation.

RECHECK TIRE PRESSURE SIGNAL

CONSULT

  1. Drive the Nissan Ariya vehicle at 25 MPH (40 km/h) or more reaches 10 minutes in total.

    NOTE:

    Avoid driving in areas with radio interference.

  2. Stop the Nissan Ariya vehicle.

  3. Select "Air pressure-front left" in "Data monitor" mode of "BCM [AIR PRESSURE MONITOR]".

  4. Check that the front left tire pressures match the standard value. .Refer to Reference Value.

Is the inspection result normal?

YES>>

After erasing DTC record, Inspection End.

NO>>

Replace BCM. Refer to Removal and Installation.

    Dtc/circuit Diagnosis. C1734-68 Tire Pressure Sensor Rl
    DTC Description NOTE: The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information....
    Dtc/circuit Diagnosis. C1742-21 Tire Pressure Sensor No Data Fr
    DTC Description NOTE: The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information....

    Other materials:

    Power Supply and Ground Circuit
    8ch Can Gateway Diagnosis Procedure CHECK FUSE Check that the following fuse are not blown. Signal name Fuse No. Battery power supply 16 Ignition power supply 9 Is the fuse blown (open)? YES>> Replace the blown fuse after repairing the affected circuit if a fuse ...

    It Can Communication Circuit
    Diagnosis Procedure CHECK NETWORK DIAGNOSIS Check the "Network diagnosis" results from CONSULT to see that the diagnostic CAN communication circuit have no malfunction. Are the diagnostic CAN communication circuit normal? YES>> GO TO 2. NO>> Check and repair diagnostic CAN commu ...

    Tcm
    Reference Value CONSULT DATA MONITOR STANDARD VALUE In CONSULT, electric shift timing or lock-up timing, i.e. operation timing of each solenoid valve, is displayed. Therefore, if there is an obvious difference between the shift timing estimated from a shift shock (or engine speed variation ...