Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: C1731-68 Tire Pressure Sensor Fl
DTC Description
NOTE:
The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.
-
Activate and display TPMS sensor IDs
-
Display tire pressure reported by the TPMS sensor
-
Read TPMS DTCs
-
Register TPMS sensor IDs
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | ||||
|---|---|---|---|---|---|---|
| C1731-68 |
Tire pressure sensor FL (Tire pressure sensor front left) |
1 | Diagnosis condition |
Drive the Nissan Ariya vehicle at 25 MPH (40 km/h) or more.
When DTC is memorized, DTC is displayed again at ignition switch ON. |
||
| Signal (terminal) | Temperature data signal. | |||||
| Threshold | Malfunction in the tire pressure data from the front left tire pressure sensor. | |||||
| Diagnosis delay time | 1 second or less. | |||||
| 2 | Diagnosis condition |
Drive the Nissan Ariya vehicle at 25 MPH (40 km/h) or more.
When DTC is memorized, DTC is displayed again at ignition switch ON. |
||||
| Signal (terminal) | Temperature data signal. | |||||
| Threshold | Malfunction in the tire temperature data from the front left tire pressure sensor. | |||||
| Diagnosis delay time | 1 second or less. | |||||
| 3 | Diagnosis condition |
Drive the Nissan Ariya vehicle at 25 MPH (40 km/h) or more.
When DTC is memorized, DTC is displayed again at ignition switch ON. |
||||
| Signal (terminal) | Temperature data signal. | |||||
| Threshold | Malfunction in the G sensor data from front left tire pressure sensor. | |||||
| Diagnosis delay time | 1 second or less. | |||||
POSSIBLE CAUSE
Front left tire pressure sensor
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
PERFORM SELF DIAGNOSIS RESULT
CONSULT
-
Ignition switch ON.
CAUTION:
Never start the engine.
-
Check tire pressure for all wheels and adjust to the specified value. Refer to Tire Air Pressure.
Is DTC “C1731-68” detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: Inspection End.
DTC Diagnosis Procedure
NOTE:
The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.
-
Activate and display TPMS sensor IDs
-
Display tire pressure reported by the TPMS sensor
-
Read TPMS DTCs
-
Register TPMS sensor IDs
PERFORM SELF DIAGNOSIS RESULT
Replace front left tire pressure sensor even if other DTCs are displayed along with “C1731-68” in “Self diagnosis result” mode of “BCM”.
>>
Replace front left tire pressure sensor. Refer to Removal & Installation .
Other materials:
Fuel Injector
Component Function Check
INSPECTION START
Turn ignition switch to START.
Are any cylinders ignited?
YES>>
GO TO 2.
NO>>
Refer to Diagnosis Procedure.
CHECK FUEL INJECTOR FUNCTION
With CONSULT
Start engine.
Perform “POWER BALANCE” in “ACTIVE TEST” mode of “E ...
Power Supply and Ground Circuit
Diagnosis Procedure
CHECK FUSIBLE LINK
Ignition switch OFF.
Check that the following fusible links are not blown (open):
Signal name Fusible link No. Capacity
Battery power supply
E
100A
D
100A
B
140A
Z
30A
Is the fusible link blown (open)?
...
With Idle Start/stop. Basic Inspection
Diagnosis and Repair Work Flow
Work Flow (With EXP-800 NI or GR8-1200 NI)
CHARGING SYSTEM DIAGNOSIS WITH EXP-800 NI OR GR8-1200 NITo test the charging system, use the following special service tools:
EXP-800 NI Battery and electrical diagnostic analyzer
GR8-1200 NI Multitasking battery and ...
