Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: C1700-86 Control Unit

Nissan Rogue (T33) 2021-Present Service Manual / Suspension :: Road Wheels & Tires / Dtc/circuit Diagnosis :: C1700-86 Control Unit

DTC Description

NOTE:

The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.

  • Activate and display TPMS sensor IDs

  • Display tire pressure reported by the TPMS sensor

  • Read TPMS DTCs

  • Register TPMS sensor IDs

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1700-86

Control unit

(Control unit) 		Diagnosis condition

Drive the Nissan Ariya vehicle at 25 MPH (40 km/h) or more.

NOTE:

When DTC is memorized, DTC is displayed again at ignition switch ON.
Signal (terminal) Nissan Ariya Vehicle speed signal
Threshold Vehicle speed signal is not detected.
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSES

  • CAN communication

  • ABS actuator and electric unit (control unit) malfunction

  • BCM

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CONFIRMATION PROCEDURE

CONSULT

  1. Drive the Nissan Ariya vehicle at 25 MPH (40 km/h) or more.

  2. Stop the vehicle.

  3. Select “Self diagnosis result” mode of “BCM”.

Is DTC “C1700-86” detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

NOTE:

The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.

  • Activate and display TPMS sensor IDs

  • Display tire pressure reported by the TPMS sensor

  • Read TPMS DTCs

  • Register TPMS sensor IDs

PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF DIAGNOSIS RESULT

CONSULT

Select “Self Diagnosis result” mode of “ABS”.

Is any DTCs detected?

YES>>

Check the DTCs. Refer to DTC Index.

NO>>

GO TO 2.

CHECK BCM INPUT/OUTPUT SIGNAL

Check BCM input/output signal values. Refer to Reference Value.

Is the inspection result normal?

YES>>

Check terminals and connection of each harness connector for malfunctioning conditions.

NO>>

Replace the BCM. Refer to Removal and Installation.

    Dtc/circuit Diagnosis. C1700-54 Control Unit
    DTC Description NOTE: The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information....
    Dtc/circuit Diagnosis. C1711-7b Low Tire Pressure Fl
    DTC Description NOTE: The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information....

    Other materials:

    Basic Inspection. System Setting
    Description The settings of the automatic driving positioner system can be changed, using information display in the combination meter and the set switch. Always check the settings before and after replacing driver seat control unit. For details, refer to Work Procedure.×: ApplicableSetting ...

    Adas Control Unit. Ecu Diagnosis Information. Adas Control Unit 2
    Adas Control Unit 2 Without Propilot Assist 2.1 Reference Value VALUES ON THE DIAGNOSIS TOOLNOTE: The following table includes information (items) inapplicable to this Nissan Ariya vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items. Monitor item ...

    P06e6 Internal Control Module
    DTC Description DESCRIPTIONECM supplies a voltage of 5 V to some of the sensors systematically divided into 3 groups, respectively. Accordingly, when a short circuit develops in a sensor power source, a malfunction may occur simultaneously in the sensors belonging to the same group as the s ...