Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: C1711-7b Low Tire Pressure Fl

Nissan Rogue (T33) 2021-Present Service Manual / Suspension :: Road Wheels & Tires / Dtc/circuit Diagnosis :: C1711-7b Low Tire Pressure Fl

DTC Description

NOTE:

The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.

  • Activate and display TPMS sensor IDs

  • Display tire pressure reported by the TPMS sensor

  • Read TPMS DTCs

  • Register TPMS sensor IDs

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1711-7B

Low tire pressure FL

(Low tire pressure front left) 		Diagnosis condition Drive at a speed of 25 MPH (40 km/h) or more reaches 10 minutes in total.
Signal (terminal) Tire pressure sensor signal.
Threshold Front left tire air pressure drops to Approx. 75% or less from the specified value.
Diagnosis delay time 10 minutes or more.

NOTE:

  • DTC may be detected depending on a tire pressure change caused by a seasonal air temperature change.

  • The low tire pressure warning lamp may be OFF due to an increase in tire internal temperature, resulted from driving.

POSSIBLE CAUSE

  • Front left tire air pressure is low

  • Air leak because of front left wheel change

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION

CONSULT

  1. Ignition switch ON.

    CAUTION:

    Never start the engine.

  2. Check the tire pressure for all wheels and adjust to the specified value. Refer to Tire Air Pressure.

  3. Select “Self diagnosis result” mode of “BCM”.

  4. Drive the Nissan Ariya vehicle at 25 MPH (40 km/h) or more until reaching 10 minutes in total.

Is DTC “C1711-7B" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

NOTE:

The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information.

  • Activate and display TPMS sensor IDs

  • Display tire pressure reported by the TPMS sensor

  • Read TPMS DTCs

  • Register TPMS sensor IDs

TIRE PRESSURE SENSOR ID REGISTRATION

Perform tire pressure sensor ID registration. Refer to Description .

Is tire pressure sensor ID registration completed?

YES>>

GO TO 2.

NO>>

Replace front left tire pressure sensor. Refer to Removal & Installation.

CHECK TIRE PRESSURE

Check the tire pressure of all wheels. Refer to Tire Air Pressure.

Is the inspection result normal?

YES>>

Perform “Confirmation Procedure” (self-diagnosis) again. Refer to DTC Description.

NO>>

GO TO 3.

CHECK TIRE PRESSURE SIGNAL

CONSULT

  1. Adjust tire pressure for all wheels to the specified value. Refer to Tire Air Pressure.

    NOTE:

    If the checked value is close to the standard, reduce the tire pressure, and then with the ignition switch ON, adjust the tire pressure again so that it is within the standard.

  2. Select "Air pressure-front left" in "Data monitor" mode of "BCM [AIR PRESSURE MONITOR]".

  3. Check that the front left tire pressures match the standard value. Refer to Reference Value.

Is the inspection result normal?

YES>>

After erasing DTC record, Inspection End.

NO>>

Replace front left tire pressure sensor. Refer to Removal & Installation.

    Dtc/circuit Diagnosis. C1700-86 Control Unit
    DTC Description NOTE: The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information....
    Dtc/circuit Diagnosis. C1731-16 Tire Pressure Sensor Fl
    DTC Description NOTE: The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information....

    Other materials:

    How to use remote keyless entry function
    WARNING Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should contact the device manufacturer for possible influences before using the Intelligent Key. The Intelligent Key transmits radio waves when the buttons are pushed. The FAA warns that such w ...

    Writing of Calibration Data
    Work Procedure DESCRIPTIONIf only the around view monitor control unit is replaced, the calibration data stored in the camera can be written to the around view monitor control unit by selecting "Camera Calibration" of "Work Support" mode in CONSULT.WORK PROCEDUREWRITE CALIBRATION DATA With C ...

    Starting the engine
    Basic information 1. Apply the parking brake. 2. Confirm that the vehicle is in the P (Park) position. The Intelligent Key must be inside the vehicle when operating the ignition switch. This is essential for proper system recognition on your Nissan Rogue. 3. Push the ignition switch to the ON po ...