Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: C1601-17 Battery Power Supply

Nissan Rogue (T33) 2021-Present Service Manual / Steering :: Steering Control System / Dtc/circuit Diagnosis :: C1601-17 Battery Power Supply

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1601 17

BATTERY VOLT

(Battery voltage) 		Diagnosis condition When ignition switch is ON.
Signal (terminal) Power supply signal
Threshold Power supply voltage is 18.2 V or more
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector

  • Power steering control module

  • Power supply system

  • Fusible link

  • Fuse

  • 12V battery

FAIL-SAFE

Manual steering state

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

  1. Pull the parking brake switch.

    NOTE:

    Check to make sure that the parking brake switch indicator is turned ON.

  2. Ignition switch OFF.

  3. Get out of the Nissan Ariya vehicle and close all doors.

  4. Wait 65 seconds.

    NOTE:

    • Check to make sure that the parking brake switch indicator is turned OFF.

    • If the rear brake calipers are hot, wait up to an hour until parking brake indicator light on the switch turns OFF. Once indicator light on the switch turns OFF, move to next step.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Perform self diagnosis for “EPS/Direct Adaptive Steering 3”.

Is DTC “C1601-17” detected?

YES>>

Proceed to diagnosis procedure. Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK POWER STEERING CONTROL MODULE POWER SUPPLY CIRCUIT

Check power steering control module power supply circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

CHECK TERMINAL

Check the power steering control module terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

Replace the power steering control module (steering gear assembly). Refer to Removal and Installation.

NO>>

Repair/replace harness, connector or terminal.

    Dtc/circuit Diagnosis. C1601-16 Battery Power Supply
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1601 16 BATTERY VOLT (Battery voltage) Diagnosis condition ...
    Dtc/circuit Diagnosis. C1604-96 Power Steering Torque Sensor
    DTC Description DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1604 96 TORQUE SENSOR (Torque sensor) Diagnosis condition When ignition switch ...

    Other materials:

    B2723-88 Corner Sensor [rr]
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen items (Trouble diagnosis content) DTC detection condition B2723-88 CORNER SENSOR [RR] (Corner sensor [RR]) Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold Communication error D ...

    Mac Key Writing
    Description When replacing around view monitor control unit, it is necessary to write MAC key to around view monitor control unit. Write MAC key to around view monitor control unit according to "MAC Key writing" procedure of "CONSULT Operation Manual". Refer to Work Procedure.CAUTION: During ...

    P2135 Tp Sensor
    DTC Description DTC DETECTION LOGICNOTE: If DTC P2135 is displayed with DTC P06B0, first perform the trouble diagnosis for DTC P06B0. Refer to DTC Description. DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2135 00 TP SENSOR-B1 (Throttle/Pedal ...