Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: C1601-16 Battery Power Supply

Nissan Rogue (T33) 2021-Present Service Manual / Steering :: Steering Control System / Dtc/circuit Diagnosis :: C1601-16 Battery Power Supply

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content) 		DTC detection condition
C1601 16

BATTERY VOLT

(Battery voltage) 		Diagnosis condition When ignition switch is ON.
Signal (terminal) Power supply signal
Threshold Power supply voltage is 8V or less
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector

  • Power steering control module

  • Power supply system

  • Fusible link

  • Fuse

  • 12V battery

FAIL-SAFE

Manual steering state

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

  1. Pull the parking brake switch.

    NOTE:

    Check to make sure that the parking brake switch indicator is turned ON.

  2. Ignition switch OFF.

  3. Get out of the Nissan Ariya vehicle and close all doors.

  4. Wait 65 seconds.

    NOTE:

    • Check to make sure that the parking brake switch indicator is turned OFF.

    • If the rear brake calipers are hot, wait up to an hour until parking brake indicator light on the switch turns OFF. Once indicator light on the switch turns OFF, move to next step.

>>

GO TO 2.

DTC REPRODUCTION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Perform self diagnosis for “EPS/Direct Adaptive Steering 3”.

Is DTC “C1601-16” detected?

YES>>

Proceed to diagnosis procedure. Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK POWER STEERING CONTROL MODULE POWER SUPPLY CIRCUIT

Check power steering control module power supply circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

CHECK TERMINAL

Check the power steering control module terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

Replace the power steering control module (steering gear assembly). Refer to Removal and Installation.

NO>>

Repair/replace harness, connector or terminal.

    Basic Inspection. Configuration
    Description Vehicle specification needs to be written with CONSULT because it is not written after replacing the power steering control module.The configuration requires network...
    Dtc/circuit Diagnosis. C1604-96 Power Steering Torque Sensor
    DTC Description DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1604 96 TORQUE SENSOR (Torque sensor) Diagnosis condition When ignition switch ...

    Other materials:

    Removal and Installation. Steering Column
    Exploded View Steering column assembly Steering shaft lower cover Clip : N·m (kg-m, ft-lb) : Always replace after every disassembly. Removal and Installation REMOVALCAUTION: Do not cause impact to steering column or shaft during removal or installation. ...

    Crankcase Pressure Sensor
    Diagnosis Procedure CHECK CRANKCASE PRESSURE SENSOR POWER SUPPLY Turn ignition switch OFF. Disconnect crankcase pressure sensor connector. Turn ignition switch ON. Check the voltage between crankcase pressure sensor harness connector terminals. + − Voltage (Approx.) C ...

    Poste de conduite
    Cette vue d’ensemble du poste de conduite du Nissan Rogue vous aide à repérer rapidement les commandes essentielles, que vous conduisiez en ville ou sur autoroute. Selon la finition de votre Nissan Rogue, certaines fonctions peuvent être présentes (signalées par *), notamment ProPILOT Assist ...