Nissan Rogue (T33) 2021-Present Service Manual: Symptom Diagnosis :: Door Does Not Lock/unlock and Engine Does Not Start (one I-Key/req Sw/push Sw)

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Symptom Diagnosis :: Door Does Not Lock/unlock and Engine Does Not Start (one I-Key/req Sw/push Sw)

Description

All doors do not lock/unlock using door request switch and engine does not start when push-button ignition switch is pressed while carrying Intelligent Key. (One Intelligent Key has the symptom, other keys operate normally.)

SYMPTOM TABLE (ONE INTELLIGENT KEY HAS THE SYMPTOM, OTHER KEYS OPERATE NORMALLY)

Door lock operation (remote keyless entry) Door lock operation (request switch of front/rear/back door) or trunk/back door open operation (opener switch of trunk/back door panel) Engine started with push-button ignition switch operation (Intelligent Key is within the detection area of inside key antenna) Engine started with push-button ignition switch operation (registered Intelligent Key placed next to push-button ignition switch) Unlock operation when approaching the Nissan Ariya vehicle, lock operation when away from the vehicle (registered Intelligent Key is within the detection area of outside key antenna)
NG NG No crank, No start OK OK

DIAGNOSIS PROCEDURE

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK INTELLIGENT KEY SYSTEM SYMPTOM TABLE

Check Intelligent Key system symptom table.

Refer to Diagnosis Procedure.

>>

GO TO 2.

CHECK INTELLIGENT KEY

Check the inside of the Intelligent Key for rust or corrosion by water. Simultaneously check the internal circuits for damage. Squeeze, twist or bend the Intelligent Key and check the functionality again. Is the Intelligent Key operating normally?

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace Intelligent Key.

CHECK INTELLIGENT KEY BATTERY

Check the Intelligent Key battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace Intelligent Key battery. Refer to Removal and Installation.

REGISTER INTELLIGENT KEY

  1. Register the Intelligent Key again.

  2. Check operation after replacement.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

GO TO 5.

REPLACE INTELLIGENT KEY

  1. Replace the Intelligent Key and perform registration again.

  2. Check operation after replacement.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

GO TO 6.

REPLACE INTELLIGENT KEY UNIT

  1. Replace Intelligent Key unit. Refer to Removal and Installation.

  2. Confirm the operation after replacement.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Check intermittent incident. Refer to Intermittent Incident.

    Symptom Diagnosis. Door Does Not Lock/unlock with Intelligent Key (one Key)
    Description All doors do not lock/unlock using Intelligent Key button. (One Intelligent Key has the symptom, other keys operate normally.)NOTE: Before starting diagnosis check t...
    Symptom Diagnosis. Intelligent Key Button Operation Has Poor Range (one Key)
    Description Intelligent Key button operation has poor range. (One Intelligent Key has the symptom, other keys operate normally.)SYMPTOM TABLE (ONE INTELLIGENT KEY HAS THE SYMPTO...

    Other materials:

    Kr15ddt. Precaution. Precautions
    Precautions Precautions for Removing Battery Terminal With the adoption of Auto ACC function, ACC power is automatically supplied by operating the Intelligent Key or remote keyless entry or by opening/closing the driver side door. In addition, ACC power is supplied even after the ignitio ...

    U0164 Can Communication
    DTC Description CAN (Controller Area Network) is a serial communication line for real time application. It is an on-Nissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a N ...

    C10b4-98 Overheat
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C10B4 98 Overheat (Overheat) Diagnosis condition When ignition switch is ON Signal (terminal) — Threshold System is high temperature status. ...