Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B2f71-24 Stop Lamp
DTC Description
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen items (Trouble diagnosis content) | DTC detecting condition | |
|---|---|---|---|
| B2F71-24 |
Stop lamp (Stop lamp) |
Diagnosis condition | Ignition switch ON |
| Signal (terminal) | Stop lamp switch 1 signal | ||
| Threshold | When stop lamp switch 1 signal is input even though the brake pedal is not depressed | ||
| Diagnosis delay time | 10 hours or more | ||
POSSIBLE CAUSE
-
Harness or connectors
(Stop lamp switch circuit is open or shorted)
-
Stop lamp switch
-
Fuse
-
BCM
FAIL-SAFE
—
CONFIRMATION PROCEDURE
DTC CONFIRMATION
CONSULT
-
Depress brake pedal 10 hours or more.
-
Ignition switch ON.
-
Select “Self diagnosis result” mode of “BCM”.
Is DTC detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: Inspection End.
DTC Diagnosis Procedure
CHECK FUSE
Check that the following fuse is not blown (open):
| Signal name | Fuse No. |
|---|---|
| Battery power supply | 32 (5 A) |
Is the fuse blown (open)?
YES>>Replace the blown (open) fuse after replacing the cause of blown (open).
NO>>GO TO 2.
CHECK STOP LAMP SWITCH SIGNAL
-
Ignition switch OFF.
-
Disconnect BCM connector.
-
Ignition switch ON.
-
Check voltage between BCM harness connector and ground.
(+) (–) Condition Voltage
(Approx.)BCM Connector Terminal E29 (with type B meter) 111 Ground Stop lamp switch 1 ON (brake pedal is not depressed) Battery voltage E60 (with type A meter) 116 Stop lamp switch 1 OFF (brake pedal is depressed) 0 V
Is the inspection normal?
YES>>Replace BCM. Refer to Removal and Installation.
NO>>GO TO 3.
CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT
-
Ignition switch OFF.
-
Disconnect stop lamp switch connector.
-
Ignition switch ON.
-
Check voltage between stop lamp switch harness connector and ground.
(+) (–) Voltage
(Approx.)Stop lamp switch Connector Terminal E38 4 Ground Battery voltage
Is the inspection result normal?
YES>>GO TO 4.
NO>>Check harness for open or short between stop lamp switch and fuse.
CHECK STOP LAMP SWITCH SIGNAL CIRCUIT
-
Ignition switch OFF.
-
Check continuity between stop lamp switch harness connector and BCM harness connector.
Stop lamp switch BCM Continuity Connector Terminal Connector Terminal E38 3 E29 (with type B meter) 111 Yes E60 (with type A meter) 116 -
Check continuity between stop lamp switch harness connector and ground.
Stop lamp switch — Continuity Connector Terminal E38 3 Ground No
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair or replace harness.
CHECK STOP LAMP SWITCH
Refer to Component Inspection.
Is the inspection result normal?
YES>>Replace BCM. Refer to Removal and Installation.
NO>>Replace stop lamp switch. Refer to Exploded View (without ProPILOT ASSIST), or Exploded View (with ProPILOT ASSIST).
Other materials:
P0532 A/c Refrigerant Pressure Sensor
DTC Description
DTC DETECTION LOGIC DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P0532
00
REFRIGERANT PRESS SENSOR A
(A/C refrigerant pressure sensor A circuit low)
Diagnosis condition
—
Signal (terminal)
Refrigerant pressure sens ...
Intelligent Key operation (models with
request switch)
Example
Example
You can conveniently lock or unlock the doors of your Nissan Rogue without taking the key out of your pocket or bag.
When you carry the Intelligent Key with you, the Nissan Rogue allows controlling all doors by pressing the door handle request switch
A (front doors) or the liftg ...
Main Line Between Lib 12v and M&a Circuit
Diagnosis Procedure
CHECK CONNECTOR
Turn the ignition switch OFF.
Disconnect the battery cable from the negative terminal.
Check the following terminals and connectors for damage, bend and loose connection (connector side and harness side).
Harness connector B41
Harness con ...