Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B2f72-23 Stop Lamp
DTC Description
DTC DETECTION LOGIC
| DTC No. |
CONSULT screen items (Trouble diagnosis content) | DTC detecting condition | |
|---|---|---|---|
| B2F72-23 |
Stop lamp (Stop lamp) |
Diagnosis condition | Ignition switch ON |
| Signal (terminal) | Stop lamp switch 2 signal | ||
| Threshold | When stop lamp switch 2 signal is input even though the brake pedal is not depressed 10 consecutive times. | ||
| Diagnosis delay time | Depress brake pedal 10 times | ||
POSSIBLE CAUSE
-
Harness or connectors
(Stop lamp switch circuit is open or shorted)
-
Stop lamp switch
-
Fuse
-
BCM
FAIL-SAFE
—
CONFIRMATION PROCEDURE
DTC CONFIRMATION
CONSULT
-
Depress brake pedal 10 times.
-
Ignition switch ON.
-
Select “Self diagnosis result” mode of “BCM”.
Is DTC detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: Inspection End.
DTC Diagnosis Procedure
CHECK FUSE
Check that the following fuse is not blown (open):
| Signal name | Fuse No. |
|---|---|
| Battery power supply | 21 (10 A) |
Is the fuse blown (open)?
YES>>Replace the blown (open) fuse after replacing the cause of blown (open).
NO>>GO TO 2.
CHECK STOP LAMP SWITCH SIGNAL
-
Ignition switch OFF.
-
Disconnect BCM connector.
-
Check voltage between BCM harness connector and ground.
(+) (–) Condition Voltage
(Approx.)BCM Connector Terminal E29 (with type B meter) 110 Ground Stop lamp switch 2 ON (brake pedal is depressed) Battery voltage E60 (with type A meter) 115 Stop lamp switch 2 OFF (brake pedal is not depressed) 0 V
Is the inspection normal?
YES>>Replace BCM. Refer to Removal and Installation.
NO>>GO TO 3.
CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT
-
Disconnect stop lamp switch connector.
-
Check voltage between stop lamp switch harness connector and ground.
(+) (–) Voltage
(Approx.)Stop lamp switch Connector Terminal E38 1 Ground Battery voltage
Is the inspection result normal?
YES>>GO TO 4.
NO>>Check harness for open or short between stop lamp switch and fuse.
CHECK STOP LAMP SWITCH SIGNAL CIRCUIT
-
Check continuity between stop lamp switch harness connector and BCM harness connector.
Stop lamp switch BCM Continuity Connector Terminal Connector Terminal E38 2 E29 (with type B meter) 110 Yes E60 (with type A meter) 115 -
Check continuity between stop lamp switch harness connector and ground.
Stop lamp switch — Continuity Connector Terminal E38 2 Ground No
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair or replace harness.
CHECK STOP LAMP SWITCH
Refer to Component Inspection.
Is the inspection result normal?
YES>>Replace BCM. Refer to Removal and Installation.
NO>>Replace stop lamp switch. Refer to Exploded View (without ProPILOT ASSIST), or Exploded View (with ProPILOT ASSIST).
Other materials:
Dtc/circuit Diagnosis. C1731-16 Tire Pressure Sensor Fl
DTC Description
NOTE:
The Signal Tech II Tool [– (NI-50190)] can be used to
perform the following functions: Refer to the Signal Tech II User Guide
for additional information.
Activate and display TPMS sensor IDs
Display tire pressure reported by the TPMS sensor
Read TPMS DTCs ...
U2a8c-88 Ethernet Circuit
DTC Description
DTC DETECTION LOGIC DTC No. CONSULT screen terms DTC detected condition
U2A8C-88
Ethernet circuit
Diagnosis condition
When ignition switch is ON.
Signal (terminal)
—
Threshold
Lost ethernet communication with AV control unit
Diagnosis delay time ...
Symptom Diagnosis. Easy Fill Tire Alert Does Not Activate
Description
The easy fill tire alert does not function while inflating a tire
when the CVT shift selector position is in P-range with the ignition
switch ON or with the engine started.NOTE:
After starting to inflate the tire, it takes a few seconds for the easy fill tire alert to function. ...