Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B2f71-23 Stop Lamp

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Security Control System / Dtc/circuit Diagnosis :: B2f71-23 Stop Lamp

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC detecting condition
B2F71-23

Stop lamp

(Stop lamp) 		Diagnosis condition When brake pedal is depressed
Signal (terminal) Stop lamp switch 1 signal
Threshold When stop lamp switch 1 signal is not input when brake pedal depressed.
Diagnosis delay time 10 hours or more

POSSIBLE CAUSE

  • Harness or connectors

    (Stop lamp switch circuit is short to battery)

  • Stop lamp switch

  • Fuse

  • BCM

FAIL-SAFE

—

CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. Depress brake pedal 10 hours or more.

  2. Ignition switch ON.

  3. Select “Self diagnosis result” mode of “BCM”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK FUSE

Check that the following fuse is not blown (open):

Signal name Fuse No.
Battery power supply 32 (5 A)

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after replacing the cause of blown (open).

NO>>

GO TO 2.

CHECK STOP LAMP SWITCH SIGNAL

  1. Ignition switch OFF.

  2. Disconnect BCM connector.

  3. Ignition switch ON.

  4. Check voltage between BCM harness connector and ground.

    (+) (–) Condition

    Voltage

    (Approx.)
    BCM
    Connector Terminal
    E29 (with type B meter) 111 Ground Stop lamp switch 1 ON (brake pedal is not depressed) Battery voltage
    E60 (with type A meter) 116 Stop lamp switch 1 OFF (brake pedal is depressed) 0 V

Is the inspection normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

GO TO 3.

CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect stop lamp switch connector.

  3. Ignition switch ON.

  4. Check voltage between stop lamp switch harness connector and ground.

    (+) (–)

    Voltage

    (Approx.)
    Stop lamp switch
    Connector Terminal
    E38 4 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Check harness for open or short between stop lamp switch and fuse.

CHECK STOP LAMP SWITCH SIGNAL CIRCUIT

  1. Ignition switch OFF.

  2. Check continuity between stop lamp switch harness connector and BCM harness connector.

    Stop lamp switch BCM Continuity
    Connector Terminal Connector Terminal
    E38 3 E29 (with type B meter) 111 Yes
    E60 (with type A meter) 116

  3. Check continuity between stop lamp switch harness connector and ground.

    Stop lamp switch — Continuity
    Connector Terminal
    E38 3 Ground No

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness.

CHECK STOP LAMP SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Replace stop lamp switch. Refer to Exploded View (without ProPILOT ASSIST), or Exploded View (with ProPILOT ASSIST).

    Dtc/circuit Diagnosis. B2f70-01 Stop Lamp
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detecting condition B2F70-01 Stop lamp (Stop lamp) Diagnosis condition When brak...
    Dtc/circuit Diagnosis. B2033-4a Dongle Ng
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detection condition B2033–4A DONGLE NG (Dongle not good) Diagnosis condition I...

    Other materials:

    Dtc/circuit Diagnosis. Power Window Relay
    Component Inspection CHECK POWER WINDOW RELAY Ignition switch OFF. Remove power window relay. Check continuity between power window relay terminals. Power window relay Condition Continuity Terminals 12 V direct current supply between terminals and . Yes No cu ...

    P11a6 Vcr Rotation Angle Sensor A/b
    DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P11A6 00 VCR rotation angle sensor mutual (Variable compression ratio rotation angle sensor mutual) Diagnosis condition Engine running at idle Signal (ter ...

    Symptom Diagnosis. Door Does Not Lock/unlock with Door Request Switch and Intelligent Key
    Description All doors do not lock/unlock using door request switch.SYMPTOM TABLE (BOTH INTELLIGENT KEYS HAVE THE SAME SYMPTOMS) Door lock operation (remote keyless entry) Door lock operation (request switch of front/rear/back door) or trunk/back door open operation (opener switch of trunk/back ...