Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B242a-11 Closure Motor

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: B242a-11 Closure Motor

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B242A-11

Closure motor

(Closure motor) 		Diagnosis condition All times
Signal (terminal) Closure motor signal
Threshold Automatic back door control unit cannot detect the closure motor signal
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector (closure motor circuit is ground open)

  • Automatic back door control unit

  • Back door lock assembly (closure motor)

FAIL-SAFE

Inhibit automatic back door system all function

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. Ignition switch ON.

  2. Select “Self diagnosis result” mode of “AUTOMATIC BACK DOOR”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK BACK DOOR CLOSURE MOTOR INPUT SIGNAL

Check voltage between automatic back door control unit harness connector and ground.

(+) (–) Condition

Voltage

(Approx.)
Automatic back door control unit
Connector Terminal
B56 33 Ground Back door closure motor Open operation Battery voltage
Other than above 5 V
34 Close operation Battery voltage
Other than above 5 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 5.

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Check the automatic back door control unit harness connector for disconnection or looseness.

  3. Check the touch sensor RH harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair/replace harness or connector, securely lock the connector, and GO TO 5.

CHECK AUTOMATIC BACK DOOR CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT

Check the automatic back door control unit power supply and ground circuits. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair/replace harness, connector, fuse, or fusible link, and GO TO 5.

CHECK TERMINAL

  1. Ignition switch OFF.

  2. Disconnect automatic back door control unit harness connector and then check the automatic back door control unit pin terminals for damage or loose connection with harness connector.

  3. Disconnect touch sensor RH harness connector and check touch sensor RH pin terminal for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

Repair/replace harness, connector, or terminal.

CHECK BACK DOOR CLOSURE MOTOR CIRCUIT

  1. Disconnect automatic back door control unit connector and back door lock assembly connector.

  2. Check continuity between automatic back door control unit harness connector and back door lock assembly harness connector.

    Automatic back door control unit Back door lock assembly Continuity
    Connector Terminal Connector Terminal
    B56 33 D512 1 Yes
    34 2

  3. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit — Continuity
    Connector Terminal
    B56 33 Ground No
    34

Is the inspection result normal?

YES>>

Replace back door lock assembly. Refer to Removal and Installation.

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis. B2428-52 Automatic Back Door Control Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2428-52 Automatic back door control unit (Automatic back do...
    Dtc/circuit Diagnosis. B242a-98 Closure Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B242A-98 Closure motor (Closure motor) Diagnosis condition W...

    Other materials:

    Removal and Installation. Drain Connector
    Exploded View Refer to Exploded View. Removal and Installation REMOVALFrontRemove instrument panel speaker. Without BOSE : Refer to Removal and Installation. With BOSE : Refer to Removal and Installation. Remove front wiper drive assembly. Refer to Removal and Installation. Dise ...

    Basic Inspection. Diagnosis and Repair Work Flow
    Work Flow DETAILS OF TROUBLE DIAGNOSIS FLOWCHARTCOLLECT THE INFORMATION FROM THE CUSTOMER It is also important to clarify customer concerns before starting the inspection. First of all, perform an interview utilizing diagnostic work sheet and reproduce the symptom as well as fully understand i ...

    P0137 Ho2s2
    DTC Description DTC DETECTION LOGICThe heated oxygen sensor 2 has a much longer switching time between rich and lean than the air fuel ratio (A/F) sensor 1. The oxygen storage capacity of the three way catalyst (manifold) causes the longer switching time. To judge the malfunctions of heated ...