Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B2428-52 Automatic Back Door Control Unit

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: B2428-52 Automatic Back Door Control Unit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B2428-52

Automatic back door control unit

(Automatic back door control unit) 		Diagnosis condition All times
Signal (terminal) —
Threshold Automatic back door control unit internal malfunction (program error)
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Automatic back door control unit

FAIL-SAFE

Inhibit automatic back door system all function

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. Ignition switch ON.

  2. Select “Self diagnosis result” mode of “AUTOMATIC BACK DOOR”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Check the automatic back door control unit harness connector for disconnection or looseness.

  3. Check the touch sensor RH harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair/replace harness or connector, and securely lock the connector..

CHECK AUTOMATIC BACK DOOR CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT

Check the automatic back door control unit power supply and ground circuits. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair/replace harness, connector, fuse, or fusible link, and GO TO 5.

CHECK TERMINAL

  1. Ignition switch OFF.

  2. Disconnect automatic back door control unit harness connector and then check the automatic back door control unit pin terminals for damage or loose connection with harness connector.

  3. Disconnect touch sensor RH harness connector and check touch sensor RH pin terminal for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

Repair/replace harness, connector, or terminal.

    Dtc/circuit Diagnosis. B2428-44 Automatic Back Door Control Unit
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2428-44 Automatic back door control unit (Automatic back do...
    Dtc/circuit Diagnosis. B242a-11 Closure Motor
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B242A-11 Closure motor (Closure motor) Diagnosis condition A...

    Other materials:

    Warning and indicator lights
    Red light Brake warning light — alerts the driver to a potential issue with the Nissan Rogue’s braking system or low brake fluid. Charge warning light — indicates a problem with the charging system or alternator. Electric shift control system warning light — shows a malfunction r ...

    B20dd-73 Ign Relay on Circ
    DTC Description IPDM E/R operates the ignition relay when it receives an ignition ON signal from BCM via CAN communication. Turn the ignition relay OFF by pressing the push-button ignition switch once when the Nissan Ariya vehicle speed is 2.5 MPH (4 km/h) or less. Turn the igniti ...

    Admission Valve
    Component Inspection CHECK ADMISSION VALVE-1 With CONSULT Turn ignition switch ON (engine stopped). Perform “ADM/V motor target angle” in “Active Test” mode of “ENGINE” using CONSULT. Operate “Up” or “Down”, set “ADM/V Target Angle” to 0 deg, and check value ...