Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B2417-15 Touch Sensor Circuit Lh Open

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: B2417-15 Touch Sensor Circuit Lh Open

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B2417-15

Touch sensor circuit LH open

(Touch sensor circuit left hand open) 		Diagnosis condition All times
Signal (terminal) Touch sensor LH signal
Threshold

Automatic back door control unit detects when one of the following conditions is satisfied

  • Touch sensor LH circuit is open or shorted

  • Malfunction of touch sensor LH
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector (touch sensor LH circuit is open or shorted)

  • Automatic back door control unit

  • Touch sensor LH

FAIL-SAFE

Inhibit automatic back door system (only operate back door closure function)

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. Ignition switch ON.

  2. Select “Self diagnosis result” mode of “AUTOMATIC BACK DOOR”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK TOUCH SENSOR INPUT SIGNAL

Check voltage between automatic back door control unit harness connector and ground.

(+) (–) Condition

Voltage

(Approx.)
Automatic back door control unit
Connector Terminal
B55 12 Ground Touch sensor LH Detect obstruction 0.2 – 3 V
Other than above 3.4 – 6.5 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 5.

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Check the automatic back door control unit harness connector for disconnection or looseness.

  3. Check the touch sensor RH harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair/replace harness or connector, securely lock the connector, and GO TO 5.

CHECK AUTOMATIC BACK DOOR CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT

Check the automatic back door control unit power supply and ground circuits. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair/replace harness, connector, fuse, or fusible link, and GO TO 5.

CHECK TERMINAL

  1. Ignition switch OFF.

  2. Disconnect automatic back door control unit harness connector and then check the automatic back door control unit pin terminals for damage or loose connection with harness connector.

  3. Disconnect touch sensor RH harness connector and check touch sensor RH pin terminal for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

Repair/replace harness, connector, or terminal.

CHECK TOUCH SENSOR CIRCUIT

  1. Disconnect automatic back door control unit connector and touch sensor LH connector.

  2. Check continuity between automatic back door control unit harness connector and touch sensor LH harness connector.

    Automatic back door control unit Touch sensor LH Continuity
    Connector Terminal Connector Terminal
    B55 12 D511 1 Yes

  3. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit — Continuity
    Connector Terminal
    B55 12 Ground No

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness.

CHECK TOUCH SENSOR GROUND CIRCUIT

  1. Disconnect touch sensor RH connector.

  2. Check continuity between automatic back door control unit harness connector and touch sensor LH harness connector.

    Automatic back door control unit Touch sensor LH Continuity
    Connector Terminal Connector Terminal
    B55 14 D511 4 Yes

  3. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit — Continuity
    Connector Terminal
    B55 14 Ground No

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace harness.

CHECK TOUCH SENSOR

Check touch sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace touch sensor RH. Refer to Removal and Installation.

    Dtc/circuit Diagnosis. B2416-15 Touch Sensor Circuit Rh Open
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2416-15 Touch sensor circuit RH open (Touch sensor circuit ...
    Dtc/circuit Diagnosis. B2419-12 Open Switch
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2419-12 Open switch (Open switch) Diagnosis condition When ...

    Other materials:

    Mac Key Writing
    Description When replacing around view monitor control unit, it is necessary to write MAC key to around view monitor control unit. Write MAC key to around view monitor control unit according to "MAC Key writing" procedure of "CONSULT Operation Manual". Refer to Work Procedure.CAUTION: During ...

    Towing load/specification
    WARNING The towing capacities in this manual are general guidelines. Actual safe towing capacity of your Nissan Rogue depends on factory or dealer-installed equipment, passenger load, and cargo weight. You must weigh both the vehicle and trailer as described to determine true towing capacity. Never ...

    Brake fluid
    For more information on brake fluid type and capacity, refer to “Capacities and recommended fluids/lubricants”. WARNING Always use new brake fluid from a sealed container. Contaminated, old, or poor-quality fluid may damage the brake system and reduce stopping performance. Clean the filler c ...