Nissan Rogue (T33) 2021-Present Service Manual: Dtc/circuit Diagnosis :: B2419-12 Open Switch

Nissan Rogue (T33) 2021-Present Service Manual / Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock / Dtc/circuit Diagnosis :: B2419-12 Open Switch

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content) 		DTC Detection Condition
B2419-12

Open switch

(Open switch) 		Diagnosis condition When the door unlock operates while ignition switch is OFF (auto ACC OFF status) or the battery terminal is removed
Signal (terminal) Open switch signal
Threshold When automatic back door control unit detect power short of open switch circuit
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector (open switch circuit is power short)

  • Automatic back door control unit

  • Back door lock assembly (open switch)

FAIL-SAFE

Inhibit automatic back door system all function

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. When the door unlock operates by Intelligent Key or door request switch while ignition switch is OFF (auto ACC OFF status).

  2. Select “Self diagnosis result” mode of “AUTOMATIC BACK DOOR”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK OPEN SWITCH INPUT SIGNAL

Check voltage between automatic back door control unit harness connector and ground.

(+) (–) Condition

Voltage

(Approx.)
Automatic back door control unit
Connector Terminal
B55 11 Ground Back door Closure operation 0 – 1 V
Other than above Battery voltage

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 5.

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Check the automatic back door control unit harness connector for disconnection or looseness.

  3. Check the touch sensor RH harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair/replace harness or connector, securely lock the connector, and GO TO 5.

CHECK AUTOMATIC BACK DOOR CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT

Check the automatic back door control unit power supply and ground circuits. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair/replace harness, connector, fuse, or fusible link, and GO TO 5.

CHECK TERMINAL

  1. Ignition switch OFF.

  2. Disconnect automatic back door control unit harness connector and then check the automatic back door control unit pin terminals for damage or loose connection with harness connector.

  3. Disconnect touch sensor RH harness connector and check touch sensor RH pin terminal for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

Repair/replace harness, connector, or terminal.

CHECK OPEN SWITCH CIRCUIT

  1. Disconnect automatic back door control unit connector and back door lock assembly connector.

  2. Check voltage between automatic back door control unit harness connector and ground.

    Automatic back door control unit —

    Voltage

    (Approx.)
    Connector Terminal
    B55 11 Ground 0 V

Is the inspection result normal?

YES>>

Replace back door lock assembly. Refer to Removal and Installation.

NO>>

Repair or replace harness.

    Dtc/circuit Diagnosis. B2416-15 Touch Sensor Circuit Rh Open
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2416-15 Touch sensor circuit RH open (Touch sensor circuit ...
    Dtc/circuit Diagnosis. B2422-78 Back Door Position Abnormal
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC Detection Condition B2422-78 Back door position abnormal (Back door position abn...

    Other materials:

    Charge Air Cooler Electric Water Pump Relay
    Component Inspection CHECK ELECTRIC WATER PUMP RELAY Turn ignition switch OFF. Remove electric water pump relay. Check the continuity between electric water pump relay terminals under the following conditions. Terminals Conditions Continuity and 12 V direct current supply ...

    Dtc/circuit Diagnosis. P161e-00 Immobilizer
    DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detecting condition P161E-00 IMMOBILIZER (Immobilizer) Diagnosis condition Ignition switch ON Signal (terminal) — Threshold When CONSULT is not used during ECM replac ...

    Removal and Installation. Fillet Molding
    Exploded View 1. Front fillet molding 2. Rear fillet molding front 3. Rear fillet molding rear 4. Grommet — — — — : Clip : Pawl : Nissan Ariya Vehicle front Front Fillet Molding Removal and Installation REMOVALRemove front fille ...